desktop-packages team mailing list archive
-
desktop-packages team
-
Mailing list archive
-
Message #157614
[Bug 1532538] Re: Build error when installing bbswitch-dkms on Ubuntu 14.04.3
I have run chkdisk as can be seen in
https://answers.launchpad.net/ubuntu/+source/bbswitch/+question/280808.
There are some errors from smartctl, but I can't really tell if they are
the cause of the kernel module problem.
Output from smartctl -a /dev/sda:
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.19.0-43-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 7200.5
Device Model: ST9750420AS
Serial Number: 5WS2N0W6
LU WWN Device Id: 5 000c50 04447820c
Firmware Version: 0002SDM1
User Capacity: 750 156 374 016 bytes [750 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Jan 21 19:31:36 2016 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 149) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 094 092 006 Pre-fail Always - 173609489
3 Spin_Up_Time 0x0003 097 097 085 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 093 093 020 Old_age Always - 7711
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 076 060 030 Pre-fail Always - 42050651
9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 14382
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2663
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 642
188 Command_Timeout 0x0032 100 096 000 Old_age Always - 76
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 074 048 045 Old_age Always - 26 (Min/Max 23/26)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 112
192 Power-Off_Retract_Count 0x0032 097 097 000 Old_age Always - 6390
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 611529
194 Temperature_Celsius 0x0022 026 052 000 Old_age Always - 26 (0 12 0 0 0)
195 Hardware_ECC_Recovered 0x001a 118 099 000 Old_age Always - 173609489
197 Current_Pending_Sector 0x0012 100 099 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0010 100 099 000 Old_age Offline - 8
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 191340793048532
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1154696376
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 84140169
SMART Error Log Version: 1
ATA Error Count: 642 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 642 occurred at disk power-on lifetime: 14354 hours (598 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 a8 95 07 00 Error: UNC at LBA = 0x000795a8 = 497064
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 a8 95 07 e0 00 00:20:56.291 READ DMA
25 00 08 ff ff ff ef 00 00:20:56.221 READ DMA EXT
c8 00 00 70 55 5e e0 00 00:20:56.161 READ DMA
c8 00 40 c0 18 28 e0 00 00:20:56.110 READ DMA
c8 00 40 00 1a 28 e0 00 00:20:56.109 READ DMA
Error 641 occurred at disk power-on lifetime: 14354 hours (598 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 a8 95 07 00 Error: UNC at LBA = 0x000795a8 = 497064
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 a8 95 07 e0 00 00:20:53.349 READ DMA
c8 00 40 00 11 28 e0 00 00:20:53.347 READ DMA
25 00 80 80 11 28 e0 00 00:20:53.326 READ DMA EXT
25 00 08 ff ff ff ef 00 00:20:53.312 READ DMA EXT
35 00 98 ff ff ff ef 00 00:20:53.310 WRITE DMA EXT
Error 640 occurred at disk power-on lifetime: 14354 hours (598 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 a8 95 07 00 Error: UNC at LBA = 0x000795a8 = 497064
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:20:49.971 READ FPDMA QUEUED
60 00 80 80 11 28 40 00 00:20:49.970 READ FPDMA QUEUED
60 00 40 00 11 28 40 00 00:20:49.970 READ FPDMA QUEUED
60 00 08 a8 95 07 40 00 00:20:49.942 READ FPDMA QUEUED
60 00 00 00 10 28 40 00 00:20:49.941 READ FPDMA QUEUED
Error 639 occurred at disk power-on lifetime: 14354 hours (598 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 a8 95 07 00 Error: UNC at LBA = 0x000795a8 = 497064
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 a8 95 07 40 00 00:20:46.822 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 00:20:46.571 FLUSH CACHE EXT
61 00 08 ff ff ff 4f 00 00:20:46.570 WRITE FPDMA QUEUED
ea 00 00 00 00 00 a0 00 00:20:46.530 FLUSH CACHE EXT
61 00 60 ff ff ff 4f 00 00:20:46.529 WRITE FPDMA QUEUED
Error 638 occurred at disk power-on lifetime: 14354 hours (598 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 a8 95 07 00 Error: UNC at LBA = 0x000795a8 = 497064
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 a8 95 07 40 00 00:20:43.711 READ FPDMA QUEUED
61 00 40 ff ff ff 4f 00 00:20:43.710 WRITE FPDMA QUEUED
61 00 d0 ff ff ff 4f 00 00:20:43.710 WRITE FPDMA QUEUED
27 00 00 00 00 00 e0 00 00:20:43.709 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:20:43.709 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
--
You received this bug notification because you are a member of Desktop
Packages, which is subscribed to bbswitch in Ubuntu.
https://bugs.launchpad.net/bugs/1532538
Title:
Build error when installing bbswitch-dkms on Ubuntu 14.04.3
Status in bbswitch package in Ubuntu:
Invalid
Bug description:
I have an Nvidia Optimus graphic card installed and have the Nvidia
driver installed and working for my Intel card, but I cannot switch to
the Nvidia card. This is because bbswitch-dkms will not build during
install via apt-get or from source.
My system
* Ubuntu 14.04.3 LTS
* NVIDIA Corporation GF119M [GeForce GT 520M]
* linux-image-3.19.0-42-generic
* linux-headers-3.19.0-42-generic
* linux-image-extra-3.19.0-42-generic
* dkms: 2.2.0.3
* gcc (Ubuntu 4.8.4-2ubuntu1~14.04) 4.8.4
* bbswitch-dkms (0.7-2ubuntu1)
When trying to install bbswitch-dkms the following error occurs:
Unpacking bbswitch-dkms (0.7-2ubuntu1) over (0.7-2ubuntu1) ...
Setting up bbswitch-dkms (0.7-2ubuntu1) ...
Loading new bbswitch-0.7 DKMS files...
Building only for 3.19.0-42-generic
Building initial module for 3.19.0-42-generic
Error! Bad return status for module build on kernel: 3.19.0-42-generic (x86_64)
Consult /var/lib/dkms/bbswitch/0.7/build/make.log for more information.
The content of make.log is:
DKMS make.log for bbswitch-0.7 for kernel 3.19.0-42-generic (x86_64)
lör 9 jan 2016 15:37:02 CET
make -C /lib/modules/3.19.0-42-generic/build M="$(pwd)" modules
make[1]: Entering directory `/usr/src/linux-headers-3.19.0-42-generic'
arch/x86/Makefile:114: stack-protector enabled but compiler support broken
CC [M] /var/lib/dkms/bbswitch/0.7/build/bbswitch.o
/var/lib/dkms/bbswitch/0.7/build/bbswitch.c: In function ‘is_card_disabled’:
/var/lib/dkms/bbswitch/0.7/build/bbswitch.c:236:1: internal compiler error: Bus error
}
^
It seems this is the main problem:
make[1]: Entering directory `/usr/src/linux-headers-3.19.0-42-generic'
arch/x86/Makefile:114: stack-protector enabled but compiler support broken
The following log entries appear in syslog during installation and
building bbswitch-dkms:
kernel: [ 235.068506] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
kernel: [ 235.071273] ata1.00: irq_stat 0x40000001
kernel: [ 235.074011] ata1.00: failed command: READ DMA
kernel: [ 235.076740] ata1.00: cmd c8/00:08:a8:95:07/00:00:00:00:00/e0 tag 27 dma 4096 in
kernel: [ 235.076740] res 51/40:00:a8:95:07/00:00:00:00:00/00 Emask 0x9 (media error)
kernel: [ 235.082207] ata1.00: status: { DRDY ERR }
kernel: [ 235.084957] ata1.00: error: { UNC }
kernel: [ 235.119639] ata1.00: configured for UDMA/133
kernel: [ 235.119667] sd 0:0:0:0: [sda] FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
kernel: [ 235.119674] sd 0:0:0:0: [sda] Sense Key : Medium Error [current] [descriptor]
kernel: [ 235.119680] sd 0:0:0:0: [sda] Add. Sense: Unrecovered read error - auto reallocate failed
kernel: [ 235.119684] sd 0:0:0:0: [sda] CDB:
kernel: [ 235.119687] Read(10): 28 00 00 07 95 a8 00 00 08 00
kernel: [ 235.119704] blk_update_request: I/O error, dev sda, sector 497064
kernel: [ 235.122090] ata1: EH complete
I have installed kernel-headers so all building packages should be
installed.
Has anyone encountered this before or know of any solutions?
Thank you!
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/bbswitch/+bug/1532538/+subscriptions
References
