← Back to team overview

kernel-packages team mailing list archive

[Bug 1586195] Re: Realtek 8153-based ethernet adapter on usb3 eventually stops working requiring unplug/replug

 

If it's any help at all: my personal laptop running Debian unstable
doesn't seem to have the same issue with this device (it's on 4.5.0).

Also, this adapter specifically is the "Monoprice USB3.0 Gigabit
Ethernet Adapter" <http://www.monoprice.com/product?p_id=11195>, which
is Realtek 8153-based as the bug title mentions.

-- 
You received this bug notification because you are a member of Kernel
Packages, which is subscribed to linux in Ubuntu.
https://bugs.launchpad.net/bugs/1586195

Title:
  Realtek 8153-based ethernet adapter on usb3 eventually stops working
  requiring unplug/replug

Status in linux package in Ubuntu:
  Triaged
Status in linux source package in Xenial:
  Triaged

Bug description:
  Seems to be paired with dmesg entries like this on the trusty kernel:

  [24763.731054] usb 4-4.2: Disable of device-initiated U1 failed.
  [24763.734507] usb 4-4.2: Disable of device-initiated U2 failed.
  [24763.734594] r815x 4-4.2:2.0 eth3: unregister 'r815x' usb-0000:00:14.0-4.2, RTL8153 ECM Device
  [24763.802963] usb 4-4.2: Set SEL for device-initiated U1 failed.
  [24763.806450] usb 4-4.2: Set SEL for device-initiated U2 failed.
  [24763.809953] usb 4-4.2: usb_reset_and_verify_device Failed to disable LTM
  [24763.809953] .
  [24763.810579] usb 4-4.2: USB disconnect, device number 7
  [24763.940765] userif-1: sent link down event.
  [24763.940769] userif-1: sent link up event.

  And like this on mainline:

  [  259.731142] usb 4-3: new SuperSpeed USB device number 4 using xhci_hcd
  [  259.752915] usb 4-3: New USB device found, idVendor=0bda, idProduct=8153
  [  259.752918] usb 4-3: New USB device strings: Mfr=1, Product=2, SerialNumber=6
  [  259.752920] usb 4-3: Product: USB 10/100/1000 LAN
  [  259.752921] usb 4-3: Manufacturer: Realtek
  [  259.752922] usb 4-3: SerialNumber: 000001000000
  [  259.909368] usb 4-3: reset SuperSpeed USB device number 4 using xhci_hcd
  [  259.993254] r8152 4-3:1.0 eth0: v1.08.3
  [  260.079151] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  [  296.266600] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  [  300.785814] r8152 4-3:1.0 eth0: Stop submitting intr, status -71
  [  302.832697] usb 4-3: usb_reset_and_verify_device Failed to disable LTM
  [  302.832697] .
  [  302.833086] usb 4-3: USB disconnect, device number 4

  Mainline version fyi:
  [    0.000000] Linux version 4.6.0-040600-generic (kernel@gomeisa) (gcc version 5.3.1 20160509 (Ubuntu 5.3.1-19ubuntu1) ) #201605151930 SMP Sun May 15 23:32:59 UTC 2016

  I also get a similar message about 'Failed to disable LTM' if I just
  unplug the device before the breakage occurs.

  I've attached lsusb before the breakage occurs (so you can see the
  device) from the mainline kernel.

  Interestingly it appears the drivers on trusty and wily/mainline are
  different (r815x vs r8152) yet still exhibit similar troubles. I'm
  still digging around to try and figure out why this doesn't seem to be
  working, but I was wondering if you all had any idea what might be
  going pear-shaped here.

  Thanks!

To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1586195/+subscriptions


References