kernel-packages team mailing list archive
-
kernel-packages team
-
Mailing list archive
-
Message #30794
[Bug 1074110] wakeonlan fails if pm-hibernate used
Forwarding as per https://bugzilla.kernel.org/show_bug.cgi?id=65361#c1
On 08/08/13 14:15, Ken Sharp wrote:
> wakeonlan fails if pm-hibernate used
>
> After issuing halt -p, wakeonlan works fine. after issuing pm-hibernate,
> the machine will not wake up.
>
> interfaces:
> auto eth0
> iface eth0 inet dhcp
> up ethtool -s eth0 wol g
> down ethtool -s eth0 wol g
>
> Settings for eth0:
> Supported ports: [ TP MII ]
> Supported link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> Supported pause frame use: No
> Supports auto-negotiation: Yes
> Advertised link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> Advertised pause frame use: No
> Advertised auto-negotiation: Yes
> Link partner advertised link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> Link partner advertised pause frame use: Symmetric
> Link partner advertised auto-negotiation: Yes
> Speed: 100Mb/s
> Duplex: Full
> Port: MII
> PHYAD: 32
> Transceiver: internal
> Auto-negotiation: on
> Supports Wake-on: pumbg
> Wake-on: g
> Current message level: 0x00000007 (7)
> drv probe link
> Link detected: yes
>
> 01:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL-8139/8139C/8139C+ (rev 10
>
> Reported on Launchpad
> https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1074110
>
> $ cat /proc/version
> Linux version 3.11.0-999-generic (apw@gomeisa) (gcc version 4.6.3
> (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #201308070514 SMP Wed Aug 7 09:24:40
> UTC 2013
>
> $ lsb_release -rd
> Description: Ubuntu 12.04.2 LTS
> Release: 12.04
>
> $ ./ver_linux
> If some fields are empty or look unusual you may have an old version.
> Compare to the current minimal requirements in Documentation/Changes.
>
> Linux oldhomeserver 3.11.0-999-generic #201308070514 SMP Wed Aug 7
> 09:24:40 UTC 2013 i686 i686 i386 GNU/Linux
>
> Gnu C 4.6
> Gnu make 3.81
> binutils 2.22
> util-linux 2.20.1
> mount support
> module-init-tools 3.16
> e2fsprogs 1.42
> pcmciautils 018
> Linux C Library 2.15
> Dynamic linker (ldd) 2.15
> Procps 3.2.8
> Net-tools 1.60
> Kbd 1.15.2
> Sh-utils 8.13
> Modules Loaded zram dm_crypt nfsd nfs_acl auth_rpcgss nfs
> fscache lockd binfmt_misc sunrpc gpio_ich lpc_ich serio_raw shpchp
> intel_rng mac_hid hwmon_vid lp parport 8139too 8139cp mii
>
> $ cat /proc/cpuinfo
> processor : 0
> vendor_id : GenuineIntel
> cpu family : 6
> model : 8
> model name : Pentium III (Coppermine)
> stepping : 3
> microcode : 0x10
> cpu MHz : 734.956
> cache size : 256 KB
> fdiv_bug : no
> f00f_bug : no
> coma_bug : no
> fpu : yes
> fpu_exception : yes
> cpuid level : 2
> wp : yes
> flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov
> pse36 mmx fxsr sse
> bogomips : 1469.91
> clflush size : 32
> cache_alignment : 32
> address sizes : 36 bits physical, 32 bits virtual
> power management:
>
> $ cat /proc/modules
> zram 18166 1 - Live 0x00000000 (C)
> dm_crypt 22524 0 - Live 0x00000000
> nfsd 246709 13 - Live 0x00000000
> nfs_acl 12771 1 nfsd, Live 0x00000000
> auth_rpcgss 49253 1 nfsd, Live 0x00000000
> nfs 162863 0 - Live 0x00000000
> fscache 52016 1 nfs, Live 0x00000000
> lockd 79198 2 nfsd,nfs, Live 0x00000000
> binfmt_misc 17268 1 - Live 0x00000000
> sunrpc 236600 23 nfsd,nfs_acl,auth_rpcgss,nfs,lockd, Live 0x00000000
> gpio_ich 13278 0 - Live 0x00000000
> lpc_ich 16987 0 - Live 0x00000000
> serio_raw 13189 0 - Live 0x00000000
> shpchp 32265 0 - Live 0x00000000
> intel_rng 12700 0 - Live 0x00000000
> mac_hid 13077 0 - Live 0x00000000
> hwmon_vid 12723 0 - Live 0x00000000
> lp 13359 0 - Live 0x00000000
> parport 40930 1 lp, Live 0x00000000
> 8139too 32770 0 - Live 0x00000000
> 8139cp 27168 0 - Live 0x00000000
> mii 13693 2 8139too,8139cp, Live 0x00000000
>
> $ cat /proc/ioports
> 0000-001f : dma1
> 0020-0021 : pic1
> 0040-0043 : timer0
> 0050-0053 : timer1
> 0060-0060 : keyboard
> 0064-0064 : keyboard
> 0070-0071 : rtc0
> 0080-008f : dma page reg
> 00a0-00a1 : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : 0000:00:1f.1
> 0170-0177 : ata_piix
> 01f0-01f7 : 0000:00:1f.1
> 01f0-01f7 : ata_piix
> 0376-0376 : 0000:00:1f.1
> 0376-0376 : ata_piix
> 03c0-03df : vga+
> 03f6-03f6 : 0000:00:1f.1
> 03f6-03f6 : ata_piix
> 0400-0403 : ACPI PM1a_EVT_BLK
> 0404-0405 : ACPI PM1a_CNT_BLK
> 0408-040b : ACPI PM_TMR
> 0410-0415 : ACPI CPU throttle
> 0428-042b : ACPI GPE0_BLK
> 042c-042f : ACPI GPE1_BLK
> 0430-0433 : iTCO_wdt
> 0460-047f : iTCO_wdt
> 0480-04bf : gpio_ich
> 0480-04bf : 0000:00:1f.0
> 04c0-04cf : 0000:00:1f.3
> 0cf8-0cff : PCI conf1
> c000-cfff : PCI Bus 0000:01
> cc00-ccff : 0000:01:03.0
> cc00-ccff : 8139too
> de00-de1f : 0000:00:1f.2
> de00-de1f : uhci_hcd
> ff00-ff0f : 0000:00:1f.1
> ff00-ff0f : ata_piix
>
> $ cat /proc/iomem
> 00000000-00000fff : reserved
> 00001000-0009fbff : System RAM
> 0009fc00-0009ffff : reserved
> 000a0000-000bffff : Video RAM area
> 000c0000-000c7fff : Video ROM
> 000e0000-000fffff : reserved
> 000f0000-000fffff : System ROM
> 00100000-0beeffff : System RAM
> 01000000-016680a2 : Kernel code
> 016680a3-019bd17f : Kernel data
> 01aa1000-01b94fff : Kernel bss
> 0bef0000-0bef7fff : ACPI Tables
> 0bef8000-0befffff : ACPI Non-volatile Storage
> 0bf00000-0bffffff : reserved
> dfc00000-dfcfffff : PCI Bus 0000:01
> e0000000-e3ffffff : 0000:00:01.0
> e7e00000-ebefffff : PCI Bus 0000:01
> e8000000-e80000ff : 0000:01:03.0
> e8000000-e80000ff : 8139too
> ee000000-ee07ffff : 0000:00:01.0
> fff80000-ffffffff : reserved
>
> $ sudo lspci -vvv
> 00:00.0 Host bridge: Intel Corporation 82810E DC-133 (GMCH) Graphics
> Memory Controller Hub (rev 03)
> Subsystem: Intel Corporation 82810E DC-133 (GMCH) Graphics Memory
> Controller Hub
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR- INTx-
> Latency: 0
> Kernel driver in use: agpgart-intel
>
> 00:01.0 VGA compatible controller: Intel Corporation 82810E DC-133 (CGC)
> Chipset Graphics Controller (rev 03) (prog-if 00 [VGA controller])
> Subsystem: Giga-byte Technology Device 0200
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
> Region 1: Memory at ee000000 (32-bit, non-prefetchable) [size=512K]
> Expansion ROM at <unassigned> [disabled]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>
> 00:1e.0 PCI bridge: Intel Corporation 82801AA PCI Bridge (rev 02)
> (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
> I/O behind bridge: 0000c000-0000cfff
> Memory behind bridge: e7e00000-ebefffff
> Prefetchable memory behind bridge: dfc00000-dfcfffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Kernel modules: shpchp
>
> 00:1f.0 ISA bridge: Intel Corporation 82801AA ISA Bridge (LPC) (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Kernel driver in use: lpc_ich
> Kernel modules: lpc_ich, intel-rng
>
> 00:1f.1 IDE interface: Intel Corporation 82801AA IDE Controller (rev 02)
> (prog-if 80 [Master])
> Subsystem: Intel Corporation 82801AA IDE Controller
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
> [size=8]
> Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
> [size=1]
> Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
> [size=8]
> Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
> [size=1]
> Region 4: I/O ports at ff00 [size=16]
> Kernel driver in use: ata_piix
>
> 00:1f.2 USB controller: Intel Corporation 82801AA USB Controller (rev
> 02) (prog-if 00 [UHCI])
> Subsystem: Intel Corporation 82801AA USB Controller
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin D routed to IRQ 10
> Region 4: I/O ports at de00 [size=32]
> Kernel driver in use: uhci_hcd
>
> 00:1f.3 SMBus: Intel Corporation 82801AA SMBus Controller (rev 02)
> Subsystem: Intel Corporation 82801AA SMBus Controller
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin B routed to IRQ 0
> Region 4: I/O ports at 04c0 [size=16]
> Kernel modules: i2c-i801
>
> 01:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL-8139/8139C/8139C+ (rev 10)
> Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64 (8000ns min, 16000ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at cc00 [size=256]
> Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0-,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: 8139too
> Kernel modules: 8139too, 8139cp
>
> $ cat /proc/scsi/scsi
> Attached devices:
> Host: scsi0 Channel: 00 Id: 01 Lun: 00
> Vendor: ATA Model: QUANTUM FIREBALL Rev: A01.
> Type: Direct-Access ANSI SCSI revision: 05
> Host: scsi1 Channel: 00 Id: 00 Lun: 00
> Vendor: GoldStar Model: CD-RW CED-8080B Rev: 1.02
> Type: CD-ROM
>
> $ ls /proc
> 1 1026 1406 1471 16 19 25 42 6 695 9 cpuinfo
> fs kpagecount mounts slabinfo tty
> 10 11 1461 1472 1641 2 26 44 619 7 986 crypto
> interrupts kpageflags mtrr softirqs uptime
> 1005 1110 1462 1473 1642 20 27 45 64 709 991 devices
> iomem latency_stats net stat version
> 1006 12 1463 1477 17 21 28 467 65 731 acpi diskstats
> ioports loadavg pagetypeinfo swaps vmallocinfo
> 1008 13 1466 1499 18 22 3 468 654 793 buddyinfo dma
> irq locks partitions sys vmstat
> 1013 1373 1467 15 1844 224 324 5 657 797 bus driver
> kallsyms mdstat sched_debug sysrq-trigger zoneinfo
> 1014 14 1468 1515 1859 225 326 579 666 8 cgroups
> execdomains kcore meminfo schedstat sysvipc
> 1021 1401 1469 1535 1867 23 39 584 67 856 cmdline fb
> key-users misc scsi timer_list
> 1023 1405 1470 1541 1868 24 41 586 694 895 consoles
> filesystems kmsg modules self timer_stats
>
> $ sudo ethtool eth0
> Settings for eth0:
> Supported ports: [ TP MII ]
> Supported link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> Supported pause frame use: No
> Supports auto-negotiation: Yes
> Advertised link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> Advertised pause frame use: No
> Advertised auto-negotiation: Yes
> Link partner advertised link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> Link partner advertised pause frame use: Symmetric
> Link partner advertised auto-negotiation: Yes
> Speed: 100Mb/s
> Duplex: Full
> Port: MII
> PHYAD: 32
> Transceiver: internal
> Auto-negotiation: on
> Supports Wake-on: pumbg
> Wake-on: g
> Current message level: 0x00000007 (7)
> drv probe link
> Link detected: yes
>
> Taken as a guide to report this:
> https://wiki.ubuntu.com/Bugs/Upstream/kernel
>
> Apologies if this is too much or not enough information, this is the
> first time I have attempted to report a problem with the kernel.
>
> I looked through https://www.kernel.org/doc/Documentation/power/ but the
> processes either didn't seem relevant or I simply didn't understand. If
> you need me to run through the processes then please let me know.
>
> Specifically
> https://www.kernel.org/doc/Documentation/power/basic-pm-debugging.txt
> suggests that the debugging would test the wake/resume cycle, which I
> don't think is relevant in this case. But I could be wrong!
>
> Thanks for your help,
>
> Ken
--
You received this bug notification because you are a member of Kernel
Packages, which is subscribed to linux in Ubuntu.
https://bugs.launchpad.net/bugs/1074110
Title:
wakeonlan fails if pm-hibernate used
Status in The Linux Kernel:
Unknown
Status in “linux” package in Ubuntu:
Confirmed
Bug description:
After issuing halt -p, wakeonlan works fine. after issuing pm-
hibernate, the machine will not wake up.
interfaces:
auto eth0
iface eth0 inet dhcp
up ethtool -s eth0 wol g
down ethtool -s eth0 wol g
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 32
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
01:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Not sure what else might be needed here, but apport-bug refuses to collect data for some reason.
https://bugs.launchpad.net/ubuntu/+source/apport/+bug/1073830
Same is true of the latest upstream kernel:
http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.7-rc3-raring/
---
Architecture: i386
DistroRelease: Ubuntu 12.04
LiveMediaBuild: Ubuntu 7.10 "Gutsy Gibbon" - Release i386 (20071016)
Package: linux 3.2.0.32.35
PackageArchitecture: i386
ProcEnviron:
TERM=xterm
LANG=en_GB.UTF-8
SHELL=/bin/bash
Uname: Linux 3.7.0-030700rc3-generic i686
UnreportableReason: The running kernel is not an Ubuntu kernel
UserGroups:
To manage notifications about this bug go to:
https://bugs.launchpad.net/linux/+bug/1074110/+subscriptions