kernel-packages team mailing list archive
-
kernel-packages team
-
Mailing list archive
-
Message #41598
[Bug 1269883] Re: Bad performance of Ethernet on USB3 port, dmesg flooded with errors
** Description changed:
- Hello,
-
- # Summary
-
-
- Plugging on USB3 port an USB-to-ethernet device yields slow performance, dmesg flooded with errors.
- Plugging on USB2 port, exact same situation otherwise, works well.
- Reproducible : not always, about 3 out of 4 attempts.
-
- # Details
-
- Observed on Asus n55s laptop with 64-bit Intel(R) Core(TM) i7-2670QM CPU @ 2.20GHz and 64-bit kernel 3.11.0-15-generic #23-Ubuntu.
- Machine has 2 USB3 ports on the left, 2 USB2 ports on the right.
-
- Device USB ID is ID 0b95:1790 ASIX Electronics Corp.
+ Plugging USB-to-ethernet device ID 0b95:1790 ASIX Electronics Corp. in
+ USB3 port yields slow performance, dmesg flooded with errors. Plugging
+ on USB2 port, exact same situation otherwise, works well. This is
+ reproducible 3 out of 4 attempts. Machine has 2 USB3 ports on the left,
+ 2 USB2 ports on the right.
### When working (USB2 port)
-
* ethernet auto-negociation is fast
* mii-tool is fast (typical 0.05s)
* few lines in dmesg
* good performance
### When failing :
-
* ethernet auto-negociation fails, then sometimes eventually works
* mii-tool is slow (10s of seconds instead of 0.05s)
time sudo mii-tool
-
eth0: no link
eth1: 10 Mbit, half duplex, no link
real 0m40.014s
user 0m0.013s
sys 0m0.006s
time sudo mii-tool
-
eth0: no link
eth1: 10 Mbit, half duplex, no link
-
real 0m50.015s
user 0m0.011s
sys 0m0.011s
time sudo mii-tool
-
eth0: no link
eth1: negotiated 100baseTx-FD, link ok
-
real 0m10.051s
user 0m0.000s
sys 0m0.012s
But on some attempts mii-tool is fast...
-
- time sudo mii-tool
-
+ time sudo mii-tool
eth0: no link
eth1: negotiated 100baseTx-FD, link ok
-
real 0m0.057s
user 0m0.011s
sys 0m0.012s
-
* DHCP eventually completes (after about 30 seconds) then ethernet works.
* whole system behaviour feels a little sluggish (not very clear, though)
* mii-tool still slow (10s of seconds instead of 0.05s)
## dmesg when failing
Full dmesg attached.
Specific lines with occurrence count at random point (obtained with
"dmesg | sed 's/^................//' | sort | uniq -c | sort -n" ).
-
- 50 ei_me 0000:00:16.0: reset: wrong host start response
- 51 ei_me 0000:00:16.0: reset: unexpected enumeration response hbm.
- 60 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
- 100 ei_me 0000:00:16.0: unexpected reset: dev_state = RESETTING
- 141 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
- 214 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
+ 50 ei_me 0000:00:16.0: reset: wrong host start response
+ 51 ei_me 0000:00:16.0: reset: unexpected enumeration response hbm.
+ 60 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
+ 100 ei_me 0000:00:16.0: unexpected reset: dev_state = RESETTING
+ 141 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
+ 214 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
Another attempt
- 11 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
- 14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
- 61 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- 61 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- 209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
- 809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
- 925 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
-
-
- 5 IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
- 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0001: -110
- 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0009: -110
- 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x000a: -110
- 6 net_ratelimit: 31 callbacks suppressed
- 9 IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
- 10 net_ratelimit: 30 callbacks suppressed
- 14 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
- 14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
- 209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
- 232 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- 232 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- 610 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
- 809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
-
-
- Jan 16 18:39:35 n55sf-l kernel: [203181.206451] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:36 n55sf-l kernel: [203181.578841] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- Jan 16 18:39:36 n55sf-l kernel: [203181.578854] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:36 n55sf-l kernel: [203182.075350] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- Jan 16 18:39:36 n55sf-l kernel: [203182.075364] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:36 n55sf-l kernel: [203182.199491] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- Jan 16 18:39:36 n55sf-l kernel: [203182.199504] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:37 n55sf-l kernel: [203182.944174] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- Jan 16 18:39:37 n55sf-l kernel: [203182.944178] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:37 n55sf-l kernel: [203183.068300] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- Jan 16 18:39:37 n55sf-l kernel: [203183.068305] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:37 n55sf-l kernel: [203183.192433] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ 11 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
+ 14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
+ 61 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ 61 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ 209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
+ 809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
+ 925 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
+
+ 5 IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
+ 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0001: -110
+ 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0009: -110
+ 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x000a: -110
+ 6 net_ratelimit: 31 callbacks suppressed
+ 9 IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
+ 10 net_ratelimit: 30 callbacks suppressed
+ 14 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
+ 14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
+ 209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
+ 232 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ 232 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ 610 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
+ 809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
+
+ Jan 16 18:39:35 n55sf-l kernel: [203181.206451] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:36 n55sf-l kernel: [203181.578841] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ Jan 16 18:39:36 n55sf-l kernel: [203181.578854] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:36 n55sf-l kernel: [203182.075350] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ Jan 16 18:39:36 n55sf-l kernel: [203182.075364] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:36 n55sf-l kernel: [203182.199491] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ Jan 16 18:39:36 n55sf-l kernel: [203182.199504] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:37 n55sf-l kernel: [203182.944174] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ Jan 16 18:39:37 n55sf-l kernel: [203182.944178] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:37 n55sf-l kernel: [203183.068300] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ Jan 16 18:39:37 n55sf-l kernel: [203183.068305] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:37 n55sf-l kernel: [203183.192433] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
## On USB2 port everything fine.
-
-
- Jan 16 18:26:44 n55sf-l kernel: [202408.897761] usb 2-1.4: new high-speed USB device number 18 using ehci-pci
- Jan 16 18:26:44 n55sf-l kernel: [202408.996745] usb 2-1.4: New USB device found, idVendor=0b95, idProduct=1790
- Jan 16 18:26:44 n55sf-l kernel: [202408.996757] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- Jan 16 18:26:44 n55sf-l kernel: [202408.996763] usb 2-1.4: Product: AX88179
- Jan 16 18:26:44 n55sf-l kernel: [202408.996769] usb 2-1.4: Manufacturer: ASIX Elec. Corp.
- Jan 16 18:26:44 n55sf-l kernel: [202408.996774] usb 2-1.4: SerialNumber: 00000000000116
- Jan 16 18:26:44 n55sf-l kernel: [202409.325222] ax88179_178a 2-1.4:1.0 eth1: register 'ax88179_178a' at usb-0000:00:1d.0-1.4, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:05:1b:a3:37:f6
- Jan 16 18:26:45 n55sf-l kernel: [202409.681691] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
- Jan 16 18:26:45 n55sf-l kernel: [202409.685338] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
- Jan 16 18:26:47 n55sf-l kernel: [202411.782132] ax88179_178a 2-1.4:1.0 eth1: ax88179 - Link status is: 1
- Jan 16 18:26:47 n55sf-l kernel: [202411.785044] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
-
- ## Once things went find on a USB3 port
-
-
- Jan 16 18:27:45 n55sf-l kernel: [202470.636671] usb 3-2: new high-speed USB device number 12 using xhci_hcd
- Jan 16 18:27:46 n55sf-l kernel: [202470.689067] usb 3-2: New USB device found, idVendor=0b95, idProduct=1790
- Jan 16 18:27:46 n55sf-l kernel: [202470.689079] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- Jan 16 18:27:46 n55sf-l kernel: [202470.689085] usb 3-2: Product: AX88179
- Jan 16 18:27:46 n55sf-l kernel: [202470.689090] usb 3-2: Manufacturer: ASIX Elec. Corp.
- Jan 16 18:27:46 n55sf-l kernel: [202470.689095] usb 3-2: SerialNumber: 00000000000116
- Jan 16 18:27:46 n55sf-l kernel: [202471.012136] ax88179_178a 3-2:1.0 eth1: register 'ax88179_178a' at usb-0000:04:00.0-2, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:05:1b:a3:37:f6
- Jan 16 18:27:46 n55sf-l kernel: [202471.367771] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
- Jan 16 18:27:46 n55sf-l kernel: [202471.371383] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
- Jan 16 18:27:48 n55sf-l kernel: [202473.414584] ax88179_178a 3-2:1.0 eth1: ax88179 - Link status is: 1
- Jan 16 18:27:48 n55sf-l kernel: [202473.416586] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
-
- ## Then bad again on next attempt on USB3 port
-
- With different infinite loop of error messages.
-
-
- 11 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
- 14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
- 61 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- 61 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- 209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
- 809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
- 925 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
-
- 5 IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
- 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0001: -110
- 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0009: -110
- 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x000a: -110
- 6 net_ratelimit: 31 callbacks suppressed
- 9 IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
- 10 net_ratelimit: 30 callbacks suppressed
- 14 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
- 14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
- 209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
- 232 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- 232 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- 610 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
- 809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
-
-
- Jan 16 18:39:35 n55sf-l kernel: [203181.206451] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:36 n55sf-l kernel: [203181.578841] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- Jan 16 18:39:36 n55sf-l kernel: [203181.578854] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:36 n55sf-l kernel: [203182.075350] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- Jan 16 18:39:36 n55sf-l kernel: [203182.075364] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:36 n55sf-l kernel: [203182.199491] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- Jan 16 18:39:36 n55sf-l kernel: [203182.199504] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:37 n55sf-l kernel: [203182.944174] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- Jan 16 18:39:37 n55sf-l kernel: [203182.944178] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:37 n55sf-l kernel: [203183.068300] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
- Jan 16 18:39:37 n55sf-l kernel: [203183.068305] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
- Jan 16 18:39:37 n55sf-l kernel: [203183.192433] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
-
-
- ## Additional attemps on USB2 port went fine.
-
-
- lsb_release -rd
-
- Description: Ubuntu 13.10
- Release: 13.10
-
- LC_ALL=C apt-cache policy linux-image-generic
-
- linux-image-generic:
- Installed: 3.11.0.15.16
- Candidate: 3.11.0.15.16
- Version table:
- *** 3.11.0.15.16 0
- 500 http://fr.archive.ubuntu.com/ubuntu/ saucy-updates/main amd64 Packages
- 500 http://security.ubuntu.com/ubuntu/ saucy-security/main amd64 Packages
- 100 /var/lib/dpkg/status
- 3.11.0.12.13 0
- 500 http://fr.archive.ubuntu.com/ubuntu/ saucy/main amd64 Packages
-
-
- Thank you for your attention.
-
-
- Googling error messages suggests a bug in kernel.
- [](https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.4.10)
- [Re: ERROR transfer event TRB DMA ptr not part of current TD -- Linux USB](http://www.spinics.net/lists/linux-usb/msg85388.html)
+ Jan 16 18:26:44 n55sf-l kernel: [202408.897761] usb 2-1.4: new high-speed USB device number 18 using ehci-pci
+ Jan 16 18:26:44 n55sf-l kernel: [202408.996745] usb 2-1.4: New USB device found, idVendor=0b95, idProduct=1790
+ Jan 16 18:26:44 n55sf-l kernel: [202408.996757] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
+ Jan 16 18:26:44 n55sf-l kernel: [202408.996763] usb 2-1.4: Product: AX88179
+ Jan 16 18:26:44 n55sf-l kernel: [202408.996769] usb 2-1.4: Manufacturer: ASIX Elec. Corp.
+ Jan 16 18:26:44 n55sf-l kernel: [202408.996774] usb 2-1.4: SerialNumber: 00000000000116
+ Jan 16 18:26:44 n55sf-l kernel: [202409.325222] ax88179_178a 2-1.4:1.0 eth1: register 'ax88179_178a' at usb-0000:00:1d.0-1.4, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:05:1b:a3:37:f6
+ Jan 16 18:26:45 n55sf-l kernel: [202409.681691] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
+ Jan 16 18:26:45 n55sf-l kernel: [202409.685338] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
+ Jan 16 18:26:47 n55sf-l kernel: [202411.782132] ax88179_178a 2-1.4:1.0 eth1: ax88179 - Link status is: 1
+ Jan 16 18:26:47 n55sf-l kernel: [202411.785044] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
+
+ ## Once things went fine on a USB3 port
+ Jan 16 18:27:45 n55sf-l kernel: [202470.636671] usb 3-2: new high-speed USB device number 12 using xhci_hcd
+ Jan 16 18:27:46 n55sf-l kernel: [202470.689067] usb 3-2: New USB device found, idVendor=0b95, idProduct=1790
+ Jan 16 18:27:46 n55sf-l kernel: [202470.689079] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
+ Jan 16 18:27:46 n55sf-l kernel: [202470.689085] usb 3-2: Product: AX88179
+ Jan 16 18:27:46 n55sf-l kernel: [202470.689090] usb 3-2: Manufacturer: ASIX Elec. Corp.
+ Jan 16 18:27:46 n55sf-l kernel: [202470.689095] usb 3-2: SerialNumber: 00000000000116
+ Jan 16 18:27:46 n55sf-l kernel: [202471.012136] ax88179_178a 3-2:1.0 eth1: register 'ax88179_178a' at usb-0000:04:00.0-2, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:05:1b:a3:37:f6
+ Jan 16 18:27:46 n55sf-l kernel: [202471.367771] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
+ Jan 16 18:27:46 n55sf-l kernel: [202471.371383] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
+ Jan 16 18:27:48 n55sf-l kernel: [202473.414584] ax88179_178a 3-2:1.0 eth1: ax88179 - Link status is: 1
+ Jan 16 18:27:48 n55sf-l kernel: [202473.416586] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
+
+ ## Then bad again on next attempt on USB3 port with different infinite loop of error messages:
+ 11 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
+ 14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
+ 61 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ 61 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ 209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
+ 809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
+ 925 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
+
+ 5 IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
+ 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0001: -110
+ 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0009: -110
+ 6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x000a: -110
+ 6 net_ratelimit: 31 callbacks suppressed
+ 9 IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
+ 10 net_ratelimit: 30 callbacks suppressed
+ 14 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
+ 14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
+ 209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
+ 232 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ 232 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ 610 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
+ 809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
+
+ Jan 16 18:39:35 n55sf-l kernel: [203181.206451] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:36 n55sf-l kernel: [203181.578841] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ Jan 16 18:39:36 n55sf-l kernel: [203181.578854] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:36 n55sf-l kernel: [203182.075350] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ Jan 16 18:39:36 n55sf-l kernel: [203182.075364] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:36 n55sf-l kernel: [203182.199491] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ Jan 16 18:39:36 n55sf-l kernel: [203182.199504] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:37 n55sf-l kernel: [203182.944174] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ Jan 16 18:39:37 n55sf-l kernel: [203182.944178] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:37 n55sf-l kernel: [203183.068300] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+ Jan 16 18:39:37 n55sf-l kernel: [203183.068305] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
+ Jan 16 18:39:37 n55sf-l kernel: [203183.192433] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
+
+ ## Additional attempts on USB2 port went fine.
+
+ https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.4.10
+ Re: ERROR transfer event TRB DMA ptr not part of current TD -- Linux USB http://www.spinics.net/lists/linux-usb/msg85388.html
ProblemType: Bug
DistroRelease: Ubuntu 13.10
Package: linux-image-3.11.0-15-generic 3.11.0-15.23
ProcVersionSignature: Ubuntu 3.11.0-15.23-generic 3.11.10
Uname: Linux 3.11.0-15-generic x86_64
ApportVersion: 2.12.5-0ubuntu2.2
Architecture: amd64
AudioDevicesInUse:
- USER PID ACCESS COMMAND
- /dev/snd/controlC0: stephane 1815 F.... pulseaudio
+ USER PID ACCESS COMMAND
+ /dev/snd/controlC0: stephane 1815 F.... pulseaudio
Date: Thu Jan 16 18:34:32 2014
HibernationDevice: RESUME=UUID=d05e8def-662d-4d3a-b3b3-4d9d2997966d
MachineType: ASUSTeK Computer Inc. N55SF
MarkForUpload: True
ProcFB: 0 inteldrmfb
ProcKernelCmdLine: BOOT_IMAGE=/boot/vmlinuz-3.11.0-15-generic root=UUID=12f862a8-f6b9-4c9e-8bf7-030b86b75241 ro quiet splash vt.handoff=7
RelatedPackageVersions:
- linux-restricted-modules-3.11.0-15-generic N/A
- linux-backports-modules-3.11.0-15-generic N/A
- linux-firmware 1.116
+ linux-restricted-modules-3.11.0-15-generic N/A
+ linux-backports-modules-3.11.0-15-generic N/A
+ linux-firmware 1.116
SourcePackage: linux
UpgradeStatus: No upgrade log present (probably fresh install)
dmi.bios.date: 08/29/2011
dmi.bios.vendor: American Megatrends Inc.
dmi.bios.version: N55SF.207
dmi.board.asset.tag: ATN12345678901234567
dmi.board.name: N55SF
dmi.board.vendor: ASUSTeK Computer Inc.
dmi.board.version: 1.0
dmi.chassis.asset.tag: No Asset Tag
dmi.chassis.type: 10
dmi.chassis.vendor: ASUSTeK Computer Inc.
dmi.chassis.version: 1.0
dmi.modalias: dmi:bvnAmericanMegatrendsInc.:bvrN55SF.207:bd08/29/2011:svnASUSTeKComputerInc.:pnN55SF:pvr1.0:rvnASUSTeKComputerInc.:rnN55SF:rvr1.0:cvnASUSTeKComputerInc.:ct10:cvr1.0:
dmi.product.name: N55SF
dmi.product.version: 1.0
dmi.sys.vendor: ASUSTeK Computer Inc.
** Tags removed: kernel-bug-exists-upstream
** Tags added: latest-bios-207 needs-upstream-testing
--
You received this bug notification because you are a member of Kernel
Packages, which is subscribed to linux in Ubuntu.
https://bugs.launchpad.net/bugs/1269883
Title:
Bad performance of Ethernet on USB3 port, dmesg flooded with errors
Status in “linux” package in Ubuntu:
Incomplete
Bug description:
Plugging USB-to-ethernet device ID 0b95:1790 ASIX Electronics Corp. in
USB3 port yields slow performance, dmesg flooded with errors. Plugging
on USB2 port, exact same situation otherwise, works well. This is
reproducible 3 out of 4 attempts. Machine has 2 USB3 ports on the
left, 2 USB2 ports on the right.
### When working (USB2 port)
* ethernet auto-negociation is fast
* mii-tool is fast (typical 0.05s)
* few lines in dmesg
* good performance
### When failing :
* ethernet auto-negociation fails, then sometimes eventually works
* mii-tool is slow (10s of seconds instead of 0.05s)
time sudo mii-tool
eth0: no link
eth1: 10 Mbit, half duplex, no link
real 0m40.014s
user 0m0.013s
sys 0m0.006s
time sudo mii-tool
eth0: no link
eth1: 10 Mbit, half duplex, no link
real 0m50.015s
user 0m0.011s
sys 0m0.011s
time sudo mii-tool
eth0: no link
eth1: negotiated 100baseTx-FD, link ok
real 0m10.051s
user 0m0.000s
sys 0m0.012s
But on some attempts mii-tool is fast...
time sudo mii-tool
eth0: no link
eth1: negotiated 100baseTx-FD, link ok
real 0m0.057s
user 0m0.011s
sys 0m0.012s
* DHCP eventually completes (after about 30 seconds) then ethernet works.
* whole system behaviour feels a little sluggish (not very clear, though)
* mii-tool still slow (10s of seconds instead of 0.05s)
## dmesg when failing
Full dmesg attached.
Specific lines with occurrence count at random point (obtained with
"dmesg | sed 's/^................//' | sort | uniq -c | sort -n" ).
50 ei_me 0000:00:16.0: reset: wrong host start response
51 ei_me 0000:00:16.0: reset: unexpected enumeration response hbm.
60 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
100 ei_me 0000:00:16.0: unexpected reset: dev_state = RESETTING
141 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
214 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
Another attempt
11 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
61 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
61 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
925 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
5 IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0001: -110
6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0009: -110
6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x000a: -110
6 net_ratelimit: 31 callbacks suppressed
9 IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
10 net_ratelimit: 30 callbacks suppressed
14 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
232 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
232 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
610 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
Jan 16 18:39:35 n55sf-l kernel: [203181.206451] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:36 n55sf-l kernel: [203181.578841] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
Jan 16 18:39:36 n55sf-l kernel: [203181.578854] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:36 n55sf-l kernel: [203182.075350] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
Jan 16 18:39:36 n55sf-l kernel: [203182.075364] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:36 n55sf-l kernel: [203182.199491] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
Jan 16 18:39:36 n55sf-l kernel: [203182.199504] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:37 n55sf-l kernel: [203182.944174] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
Jan 16 18:39:37 n55sf-l kernel: [203182.944178] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:37 n55sf-l kernel: [203183.068300] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
Jan 16 18:39:37 n55sf-l kernel: [203183.068305] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:37 n55sf-l kernel: [203183.192433] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
## On USB2 port everything fine.
Jan 16 18:26:44 n55sf-l kernel: [202408.897761] usb 2-1.4: new high-speed USB device number 18 using ehci-pci
Jan 16 18:26:44 n55sf-l kernel: [202408.996745] usb 2-1.4: New USB device found, idVendor=0b95, idProduct=1790
Jan 16 18:26:44 n55sf-l kernel: [202408.996757] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Jan 16 18:26:44 n55sf-l kernel: [202408.996763] usb 2-1.4: Product: AX88179
Jan 16 18:26:44 n55sf-l kernel: [202408.996769] usb 2-1.4: Manufacturer: ASIX Elec. Corp.
Jan 16 18:26:44 n55sf-l kernel: [202408.996774] usb 2-1.4: SerialNumber: 00000000000116
Jan 16 18:26:44 n55sf-l kernel: [202409.325222] ax88179_178a 2-1.4:1.0 eth1: register 'ax88179_178a' at usb-0000:00:1d.0-1.4, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:05:1b:a3:37:f6
Jan 16 18:26:45 n55sf-l kernel: [202409.681691] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 16 18:26:45 n55sf-l kernel: [202409.685338] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 16 18:26:47 n55sf-l kernel: [202411.782132] ax88179_178a 2-1.4:1.0 eth1: ax88179 - Link status is: 1
Jan 16 18:26:47 n55sf-l kernel: [202411.785044] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
## Once things went fine on a USB3 port
Jan 16 18:27:45 n55sf-l kernel: [202470.636671] usb 3-2: new high-speed USB device number 12 using xhci_hcd
Jan 16 18:27:46 n55sf-l kernel: [202470.689067] usb 3-2: New USB device found, idVendor=0b95, idProduct=1790
Jan 16 18:27:46 n55sf-l kernel: [202470.689079] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Jan 16 18:27:46 n55sf-l kernel: [202470.689085] usb 3-2: Product: AX88179
Jan 16 18:27:46 n55sf-l kernel: [202470.689090] usb 3-2: Manufacturer: ASIX Elec. Corp.
Jan 16 18:27:46 n55sf-l kernel: [202470.689095] usb 3-2: SerialNumber: 00000000000116
Jan 16 18:27:46 n55sf-l kernel: [202471.012136] ax88179_178a 3-2:1.0 eth1: register 'ax88179_178a' at usb-0000:04:00.0-2, ASIX AX88179 USB 3.0 Gigabit Ethernet, 00:05:1b:a3:37:f6
Jan 16 18:27:46 n55sf-l kernel: [202471.367771] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 16 18:27:46 n55sf-l kernel: [202471.371383] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 16 18:27:48 n55sf-l kernel: [202473.414584] ax88179_178a 3-2:1.0 eth1: ax88179 - Link status is: 1
Jan 16 18:27:48 n55sf-l kernel: [202473.416586] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
## Then bad again on next attempt on USB3 port with different infinite loop of error messages:
11 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
61 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
61 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
925 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
5 IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0001: -110
6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0009: -110
6 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x000a: -110
6 net_ratelimit: 31 callbacks suppressed
9 IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
10 net_ratelimit: 30 callbacks suppressed
14 ax88179_178a 4-1:1.0 eth1: Failed to read reg index 0x0000: -110
14 ax88179_178a 4-1:1.0 eth1: Failed to write reg index 0x0002: -110
209 ax88179_178a 4-1:1.0 eth1: kevent 4 may have been dropped
232 xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
232 xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
610 xhci_hcd 0000:04:00.0: ERROR Transfer event TRB DMA ptr not part of current TD
809 ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
Jan 16 18:39:35 n55sf-l kernel: [203181.206451] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:36 n55sf-l kernel: [203181.578841] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
Jan 16 18:39:36 n55sf-l kernel: [203181.578854] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:36 n55sf-l kernel: [203182.075350] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
Jan 16 18:39:36 n55sf-l kernel: [203182.075364] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:36 n55sf-l kernel: [203182.199491] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
Jan 16 18:39:36 n55sf-l kernel: [203182.199504] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:37 n55sf-l kernel: [203182.944174] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
Jan 16 18:39:37 n55sf-l kernel: [203182.944178] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:37 n55sf-l kernel: [203183.068300] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
Jan 16 18:39:37 n55sf-l kernel: [203183.068305] xhci_hcd 0000:04:00.0: A Set TR Deq Ptr command is pending.
Jan 16 18:39:37 n55sf-l kernel: [203183.192433] xhci_hcd 0000:04:00.0: WARN Cannot submit Set TR Deq Ptr
## Additional attempts on USB2 port went fine.
https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.4.10
Re: ERROR transfer event TRB DMA ptr not part of current TD -- Linux USB http://www.spinics.net/lists/linux-usb/msg85388.html
ProblemType: Bug
DistroRelease: Ubuntu 13.10
Package: linux-image-3.11.0-15-generic 3.11.0-15.23
ProcVersionSignature: Ubuntu 3.11.0-15.23-generic 3.11.10
Uname: Linux 3.11.0-15-generic x86_64
ApportVersion: 2.12.5-0ubuntu2.2
Architecture: amd64
AudioDevicesInUse:
USER PID ACCESS COMMAND
/dev/snd/controlC0: stephane 1815 F.... pulseaudio
Date: Thu Jan 16 18:34:32 2014
HibernationDevice: RESUME=UUID=d05e8def-662d-4d3a-b3b3-4d9d2997966d
MachineType: ASUSTeK Computer Inc. N55SF
MarkForUpload: True
ProcFB: 0 inteldrmfb
ProcKernelCmdLine: BOOT_IMAGE=/boot/vmlinuz-3.11.0-15-generic root=UUID=12f862a8-f6b9-4c9e-8bf7-030b86b75241 ro quiet splash vt.handoff=7
RelatedPackageVersions:
linux-restricted-modules-3.11.0-15-generic N/A
linux-backports-modules-3.11.0-15-generic N/A
linux-firmware 1.116
SourcePackage: linux
UpgradeStatus: No upgrade log present (probably fresh install)
dmi.bios.date: 08/29/2011
dmi.bios.vendor: American Megatrends Inc.
dmi.bios.version: N55SF.207
dmi.board.asset.tag: ATN12345678901234567
dmi.board.name: N55SF
dmi.board.vendor: ASUSTeK Computer Inc.
dmi.board.version: 1.0
dmi.chassis.asset.tag: No Asset Tag
dmi.chassis.type: 10
dmi.chassis.vendor: ASUSTeK Computer Inc.
dmi.chassis.version: 1.0
dmi.modalias: dmi:bvnAmericanMegatrendsInc.:bvrN55SF.207:bd08/29/2011:svnASUSTeKComputerInc.:pnN55SF:pvr1.0:rvnASUSTeKComputerInc.:rnN55SF:rvr1.0:cvnASUSTeKComputerInc.:ct10:cvr1.0:
dmi.product.name: N55SF
dmi.product.version: 1.0
dmi.sys.vendor: ASUSTeK Computer Inc.
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1269883/+subscriptions
References
