kernel-packages team mailing list archive
-
kernel-packages team
-
Mailing list archive
-
Message #59252
[Bug 1316284] Re: Load/Unload Cycle Count
Laptop is HP Probook 4540s with Seagate 750GB HDD.
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus SpinPoint M8 (AF)
Device Model: ST750LM022 HN-M750MBB
Serial Number: S2SUJ9KC909317
LU WWN Device Id: 5 0004cf 2085c649e
Firmware Version: 2AR10002
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue May 6 13:53:33 2014 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9780) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 163) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 13
2 Throughput_Performance 0x0027 252 252 000 Pre-fail Always - 0
3 Spin_Up_Time 0x0023 089 089 025 Pre-fail Always - 3456
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1233
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 252 252 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 252 252 015 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 4116
10 Spin_Retry_Count 0x0033 252 252 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 409
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1204
181 Program_Fail_Cnt_Total 0x0022 100 100 000 Old_age Always - 9806512
183 Runtime_Bad_Block 0x0032 252 252 010 Old_age Always - 0
184 End-to-End_Error 0x0033 252 252 048 Pre-fail Always - 0
186 Unknown_Attribute 0x0032 252 252 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 252 252 000 Old_age Always - 0
188 Command_Timeout 0x0032 252 252 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0002 074 056 040 Old_age Always - 26 (Min/Max 15/45)
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 63
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 091 091 000 Old_age Always - 92145
194 Temperature_Celsius 0x0002 064 056 000 Old_age Always - 26 (Min/Max 15/45)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 7281
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 4110 -
# 2 Short offline Completed without error 00% 4108 -
# 3 Short offline Completed without error 00% 4104 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
///////////////////////////////////////////////////////////////////////////////////////////////////////////
Last night I noticed that cycles are now getting higher even with AC.
On Windows this is not happening on the AC or battery.
--
You received this bug notification because you are a member of Kernel
Packages, which is subscribed to linux in Ubuntu.
https://bugs.launchpad.net/bugs/1316284
Title:
Load/Unload Cycle Count
Status in “linux” package in Ubuntu:
Incomplete
Bug description:
I have a little a bit of a problem with my Ubuntu.
My Load/Unload Cycle Count is currently at 92125.
The problem is that Load/Unload Cycle Count get higher every time I use my laptop on battery mode.
With AC it seems fine, but with battery in a matter of a few minutes (1-2) my Load/Unload Cycle Count gets higer for 3 numbers.
I checked it on Windows, and it was at 92117. Then I booted in Ubuntu
and the number climed at 92121. I used laptop on AC for 20 minutes and
then it was at 92122. Then I unpluged AC, and used my laptop on
battery for few minutes and the number was at 92125. Then again on AC
for 15 minutes and it was at 92125. So it gets high quickly on
battery, very quickly.
Also I hear scratching noise of HDD when Ubuntu opens Files, Firefox os something like that.
On Windows I almost never hear that, only when doing something hard for HDD.
This is happening on my 750GB Seagate disk.
Running Ubuntu 14.04 LTS with Windows 7 dual boot.
ProblemType: Bug
DistroRelease: Ubuntu 14.04
Package: unity 7.2.0+14.04.20140423-0ubuntu1.2
ProcVersionSignature: Ubuntu 3.13.0-24.46-generic 3.13.9
Uname: Linux 3.13.0-24-generic x86_64
NonfreeKernelModules: fglrx
ApportVersion: 2.14.1-0ubuntu3
Architecture: amd64
CompizPlugins: No value set for `/apps/compiz-1/general/screen0/options/active_plugins'
Date: Mon May 5 21:14:44 2014
EcryptfsInUse: Yes
InstallationDate: Installed on 2014-04-17 (18 days ago)
InstallationMedia: Ubuntu 14.04 LTS "Trusty Tahr" - Release amd64 (20140417)
SourcePackage: unity
UpgradeStatus: No upgrade log present (probably fresh install)
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1316284/+subscriptions
