kicad-developers team mailing list archive

[Maciej Sumiński <maciej.suminski@xxxxxxx>]

Should be fine with revision 5031. Please let me know if everything is fine.

Regards,
Orson

On 07/28/2014 01:06 PM, Maciej Sumiński wrote:
> Thank you Andrew, I have merged the branch you had proposed. I will
> investigate the vanishing pads issue soon.
>
> Regards,
> Orson
>
> On 07/27/2014 08:54 PM, Andrew Zonenberg wrote:
> > The attached patch fixes the crash but it appears that the vanishing
> > pads is a separate, unrelated bug.
> >
> > Want me to look into that too? The crash was my main priority (my focus
> > right now is fixing bugs that keep me from getting my work done) but if
> > I get time I can investigate the disappearing pad bug too.
> >
> > On Sun, 2014-07-27 at 14:36 -0400, Andrew Zonenberg wrote:
> > > Interesting. I'll add a divide-by-zero check to the line that it died on
> > > and see if that fixes the problem. Will send a patch if it works.
> > >
> > > On Sun, 2014-07-27 at 20:32 +0200, Nick Østergaard wrote:
> > > > Tried it with your exact settings, no difference. I do see that the
> > > > preview vanishes when I enter zero in that field, and will not refresh
> > > > even if I write a non-zero value -- untill I accpet the settings and
> > > > open the properties again. But my build is not a debug build, so I
> > > > guess that the exception you get is just silenced for me.
> > > >
> > > > 2014-07-27 20:23 GMT+02:00 Andrew Zonenberg
> > > > <azonenberg@xxxxxxxxxxxxxxx>:
> > > > > Exact pad properties I was using if it's any help:
> > > > >
> > > > > http://i.imgur.com/DvnE9sI.png
> > > > >
> > > > > http://i.imgur.com/1f32yDz.png
> > > > >
> > > > > Fully reproducible, I can trigger it on command.
> > > > >
> > > > > On Sun, 2014-07-27 at 20:22 +0200, Nick Østergaard wrote:
> > > > > > I cannot reproduce with 5018 on linux.
> > > > > >
> > > > > > 2014-07-27 20:17 GMT+02:00 Andrew Zonenberg
> > > > > > <azonenberg@xxxxxxxxxxxxxxx>:
> > > > > > > Steps to reproduce:
> > > > > > > * Open the GAL module editor
> > > > > > > * Add a new pad to the module
> > > > > > > * Highlight the "size X" field
> > > > > > > * Begin to type "0.5" or any other decimal with a leading zero
> > > > > > > * As soon as the "0" is entered, a SIGFPE is thrown
> > > > > > >
> > > > > > > --
> > > > > > > Andrew Zonenberg
> > > > > > > PhD student, security group
> > > > > > > Computer Science Department
> > > > > > > Rensselaer Polytechnic Institute
> > > > > > > http://colossus.cs.rpi.edu/~azonenberg/
> > > > > > >
> > > > > > > _______________________________________________
> > > > > > > Mailing list: https://launchpad.net/~kicad-developers
> > > > > > > Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
> > > > > > > Unsubscribe : https://launchpad.net/~kicad-developers
> > > > > > > More help   : https://help.launchpad.net/ListHelp
> > > > >
> > > > > --
> > > > > Andrew Zonenberg
> > > > > PhD student, security group
> > > > > Computer Science Department
> > > > > Rensselaer Polytechnic Institute
> > > > > http://colossus.cs.rpi.edu/~azonenberg/
> > >
> > > _______________________________________________
> > > Mailing list: https://launchpad.net/~kicad-developers
> > > Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
> > > Unsubscribe : https://launchpad.net/~kicad-developers
> > > More help   : https://help.launchpad.net/ListHelp
> >
> >
> >
> > _______________________________________________
> > Mailing list: https://launchpad.net/~kicad-developers
> > Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
> > Unsubscribe : https://launchpad.net/~kicad-developers
> > More help   : https://help.launchpad.net/ListHelp
>
>
> _______________________________________________
> Mailing list: https://launchpad.net/~kicad-developers
> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
> Unsubscribe : https://launchpad.net/~kicad-developers
> More help   : https://help.launchpad.net/ListHelp