kicad-developers team mailing list archive

[Wayne Stambaugh <stambaughw@xxxxxxxxx>]

How does this bus connect to another bus without a label that looks
something like A[19..32] on other open ended buses?  Unless the bus is
directly connected I believe the label is required.

FYI.  I need to get my eyes checked.  If a wire doesn't end on the label
connection point, then open ended wires are shown as unconnected.  It
looks the dangling end test is in need of some improvement.  Again, see
the video demo.  There are examples of both cases.

On 6/9/2015 3:24 PM, Chris Pavlina wrote:
> No, I just mean things like this:
> 
> http://misc.c4757p.com/bus.png
> 
> The bus is very frequently drawn past the end of a row of connections to 
> emphasize the fact that it is a bus.
> 
> (Imagine the bit going off to the right goes somewhere else.)
> 
> On Tue, Jun 09, 2015 at 03:17:52PM -0400, Wayne Stambaugh wrote:
>> Yes, but typically in open ended bus use case they have a label attached
>> to them that makes the connection.  The same thing can be done with
>> wires which does show the connection status correctly when a wire is
>> open ended but has a label attached to it.  The video demo project is a
>> good example of both behaviors.  It's not that important but some users
>> may wonder why the difference between wire and bus connections.  It's
>> something to think about.
>>
>> On 6/9/2015 2:30 PM, Chris Pavlina wrote:
>>> I'm not sure about that one - it's common to draw buses in a manner that 
>>> leaves their ends open.
>>>
>>> On Tue, Jun 09, 2015 at 01:43:56PM -0400, Wayne Stambaugh wrote:
>>>> I've tried this patch and it works as expected.  Good work Chris.  Does
>>>> anyone have any objections to this patch before I commit it?
>>>>
>>>> One other thing I noticed is the bus wires (and I'm guessing bus entries
>>>> as well) do not have any segment end point connection indicators.  It
>>>> would be nice if they supported them as well.
>>>>
>>>> On 6/8/2015 5:38 PM, Chris Pavlina wrote:
>>>>> Hi,
>>>>>
>>>>> I already sent in this patch but as a reply to my existing pin targets 
>>>>> thread; I think it may have got lost. This patch enables pin "targets" 
>>>>> on bus entries as well, as Wayne suggested, and hides them when the bus 
>>>>> entry is connected.
>>>>>
>>>>> --
>>>>> Chris
>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Mailing list: https://launchpad.net/~kicad-developers
>>>>> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
>>>>> Unsubscribe : https://launchpad.net/~kicad-developers
>>>>> More help   : https://help.launchpad.net/ListHelp
>>>>>
>>>>
>>>> _______________________________________________
>>>> Mailing list: https://launchpad.net/~kicad-developers
>>>> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
>>>> Unsubscribe : https://launchpad.net/~kicad-developers
>>>> More help   : https://help.launchpad.net/ListHelp
>>>
>>> _______________________________________________
>>> Mailing list: https://launchpad.net/~kicad-developers
>>> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
>>> Unsubscribe : https://launchpad.net/~kicad-developers
>>> More help   : https://help.launchpad.net/ListHelp
>>>
>>
>> _______________________________________________
>> Mailing list: https://launchpad.net/~kicad-developers
>> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
>> Unsubscribe : https://launchpad.net/~kicad-developers
>> More help   : https://help.launchpad.net/ListHelp
> 
> _______________________________________________
> Mailing list: https://launchpad.net/~kicad-developers
> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
> Unsubscribe : https://launchpad.net/~kicad-developers
> More help   : https://help.launchpad.net/ListHelp
>