kicad-developers team mailing list archive

[Adam Wolf <adamwolf@xxxxxxxxxxxxxxxxxxxx>]

Hi Bob!

There are no code changes in this RC2 package from the nightlies.  I made a
new autobuilder for this build, and was looking for testers to make sure
the autobuilder seems ok.

It does.

Thanks!

Adam Wolf
Cofounder and Engineer
W&L

On Fri, Nov 13, 2015 at 11:49 AM, Bob Gustafson <bobgus@xxxxxxx> wrote:

> Whoops - comments on my previous message only apply to eeschema view.
>
> The pcbnew view (openGL) will scroll so picture is 1/10 the area of the
> window, rather than stopping when whole paper is visible in the window.
>
> Scrolling and Zooming is jumpy and slow.
>
> Scrolling requires two finger + shift to go up and down. two finger +
> command to go left right (and picture motion is opposite to finger motion)
>
> Scrolling should be the same as eechema - two finger + shift gives two
> dimensional scroll - very intuitive.
>
> Still needs some work.
>
> Bob G
>
>
> On 11/13/2015 11:03 AM, Bob Gustafson wrote:
>
> Wow - lots of reasonable changes to the OSX version:
>
>   Two finger + Shift - trackpad works intuitively like it should (at least
> for me) - move fingers left, picture moves left, move fingers up, picture
> moves up, and scroll stops when edge of paper is reached.
>
>   Two finger - trackpad zoom works more slowly and smoothly.
>
> I haven't tested beyond the trackpad motions for now (as these were
> blockers for me).
>
> Thanks much to the whole team - including the OSXers.
>
> Bob G
>
> On 11/13/2015 10:01 AM, Adam Wolf wrote:
>
> Both should work.  It was me tweaking things that shouldn't impact the
> build, things like Jenkins retries and timeouts and stuff like that.
>
> On Fri, Nov 13, 2015 at 9:51 AM, Johannes Maibaum < <jmaibaum@xxxxxxxxx>
> jmaibaum@xxxxxxxxx> wrote:
>
>> Hi Adam,
>>
>> > Am 13.11.2015 um 15:32 schrieb Adam Wolf <
>> <adamwolf@xxxxxxxxxxxxxxxxxxxx>adamwolf@xxxxxxxxxxxxxxxxxxxx>:
>> >
>> > Hi folks,
>> >
>> > I uploaded test packages of kicad and kicad-extras from the RC2 branch
>> to the regular nightlies area.  If someone else could download them and
>> make sure they seem OK before publicizing this, that would be appreciated.
>> >
>> > http://downloads.kicad-pcb.org/osx/
>>
>> In that folder, there two packages each (2x kicad-4.0.0-rc2… and 2x
>> kicad-extras-4.0.0-rc2) that, from their names, look to be built from
>> identical snapshots, but at different times.
>>
>> Is their any reason I should check both builds? I’m currently only
>> downloading the newer ones…
>>
>>
>> Best,
>>
>> Johannes
>>
>> >
>> > Thanks!
>> >
>> > Adam Wolf
>> > Cofounder and Engineer
>> > W&L
>>
>> _______________________________________________
>> Mailing list: https://launchpad.net/~kicad-developers
>> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
>> Unsubscribe : https://launchpad.net/~kicad-developers
>> More help   : https://help.launchpad.net/ListHelp
>>
>
>
>
> _______________________________________________
> Mailing list: https://launchpad.net/~kicad-developers
> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
> Unsubscribe : https://launchpad.net/~kicad-developers
> More help   : https://help.launchpad.net/ListHelp
>
>
>
>
> _______________________________________________
> Mailing list: https://launchpad.net/~kicad-developers
> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
> Unsubscribe : https://launchpad.net/~kicad-developers
> More help   : https://help.launchpad.net/ListHelp
>
>
>
> _______________________________________________
> Mailing list: https://launchpad.net/~kicad-developers
> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
> Unsubscribe : https://launchpad.net/~kicad-developers
> More help   : https://help.launchpad.net/ListHelp
>
>