Hi,
I add array feature to my Via Stitching. And an another slowly video
to watch.
https://youtu.be/28nfoZPg2bg
Full fixed patch and array test patch. More work have to be done, but
this was easy start.
Regards
Heikki
On Thu, Oct 13, 2016 at 7:23 PM, Heikki Pulkkinen <hei6mail@xxxxxxxxx
<mailto:hei6mail@xxxxxxxxx>> wrote:
Hi,
Here is demovideo about via stitching. It is slowly, because of
slowly machine. I do some development too, so full patch is
attached too.
On Tue, Oct 11, 2016 at 5:49 PM, Marcos Chaparro
<nitrousnrg@xxxxxxxxx <mailto:nitrousnrg@xxxxxxxxx>> wrote:
Hi Heikki,
is there any chance to make some screenshots or video about
this? Some of us do compile kicad to get the latest and
greatest but never applied a patch for a particular feature.
Regards
Marcos
On Sat, Oct 8, 2016 at 7:04 AM, Heikki Pulkkinen
<hei6mail@xxxxxxxxx <mailto:hei6mail@xxxxxxxxx>> wrote:
Hi,
Putting back that my via stitching tool to routing tool.
It is better that way, I think. All via tools are in same
place, and it adds vias to pours only from hotkeys.
On Sun, Oct 2, 2016 at 12:28 PM, Heikki Pulkkinen
<hei6mail@xxxxxxxxx <mailto:hei6mail@xxxxxxxxx>> wrote:
Hi,
Finally Via Stitching without tracks is at zone tool.
I tested it little bit, but more tests are needed.
This patch replace all other patches. Do not use them,
use only this patch. I think this is worth of try. I
am going to use it anyway, even if it do not get any
acceptance. First patch is for Fedora users. It makes
possible to build Kicad in Fedora release wxWidgets
libs whitout building wxWidget from source. I do not
know has anybody else that problem, but I had.
Heikki
On Tue, Sep 27, 2016 at 6:46 PM, Heikki Pulkkinen
<hei6mail@xxxxxxxxx <mailto:hei6mail@xxxxxxxxx>> wrote:
Hi
And I really practice. I made improvement and
forgot to copy all. So improvement is in these two
patches. I hope this suggestion is accepted as a
new feature.
Heikki
On Tue, Sep 27, 2016 at 2:31 PM, Heikki Pulkkinen
<hei6mail@xxxxxxxxx <mailto:hei6mail@xxxxxxxxx>>
wrote:
Hi,
As in practice, I made a patch file of my
changes Not only diifs. It is SHIFT-ALT-V
hotkey whitch make buried and blind vias, as
it is in routing too.
Heikki
On Sun, Sep 25, 2016 at 2:25 PM, Heikki
Pulkkinen <hei6mail@xxxxxxxxx
<mailto:hei6mail@xxxxxxxxx>> wrote:
Hi,
I made some improvements to my patch of
via stitching. Now you can just point
copper pour place and press V, it make
trough via. If you press SHIFT+CTRL+V it
make buried or blind via.It does not
change working layer. Only when you place
buried or blind via from different layer
than it's layer pair is. I think that it
is quite easy to shoot board full of
copper pours connecting vias. It is
possible to remove connecting tracks from
old designs. Just delete connection from
pad and use clenup. Only have to remember
that if there are not at least two copper
pours in same netcode in different layers
via is deleted too. Any support?
Heikki
On Sat, Sep 24, 2016 at 3:06 PM, Heikki
Pulkkinen <hei6mail@xxxxxxxxx
<mailto:hei6mail@xxxxxxxxx>> wrote:
Hi everybody,
This is my suggestion to via stitching
without any tracks. It connects
unconnected vias in different copper
pours witch has same netcode. Adding
vias is normal routing process without
routing tracks. Start - Change Layer -
End. Tool that do those things
automatically would be good, so you
can add all vias in same layer. After
adding vias, run "Fill or Refill All
Zones" that "Clenup tracks and vias"
do not remove partly connected vias.
Heikki
_______________________________________________
Mailing list: https://launchpad.net/~kicad-developers
<https://launchpad.net/%7Ekicad-developers>
Post to : kicad-developers@xxxxxxxxxxxxxxxxxxx
<mailto:kicad-developers@xxxxxxxxxxxxxxxxxxx>
Unsubscribe : https://launchpad.net/~kicad-developers
<https://launchpad.net/%7Ekicad-developers>
More help : https://help.launchpad.net/ListHelp
<https://help.launchpad.net/ListHelp>
_______________________________________________
Mailing list: https://launchpad.net/~kicad-developers
Post to : kicad-developers@xxxxxxxxxxxxxxxxxxx
Unsubscribe : https://launchpad.net/~kicad-developers
More help : https://help.launchpad.net/ListHelp
