opensand team mailing list archive

[Dubois Emmanuel <Emmanuel.Dubois@xxxxxxx>]

Hello, 
good to hear that the problem is solved. 
I send to the mailing list your answer to close the beginned discussion.

Don't hesitate to use directly the mailing list. This can be useful for other users who will have the same problem.

See you next week, 

Cordially
Emmanuel

-------------------------------- 
Emmanuel DUBOIS, CNES (Lagrange S28)
(+33) 5 61 28 19 81

-----Message d'origine-----
De : TUZET Francois [mailto:Francois.TUZET@xxxxxxxxxxxxxx] 
Envoyé : mercredi 12 février 2014 11:28
À : Dubois Emmanuel
Cc : VERLEY Jonas
Objet : RE: Enable to connect to state server

Hello,
We have solved our installation problem it was just a mistake with eth0 and eth1! So it's not usefull to forward our message to the mailing list.
However, thank you for your quick answer and we'll ask you about some points when we meet.

Cordialy,

François and Jonas





Le 11.02.2014 19:23, Dubois Emmanuel a écrit :
> Hello,
> First of all, I forward the email to the mailing list of OpenSAND so 
> that more people can answer your needs and to keep a trace of your 
> problem in the archive.
>
> Secondly, it is difficult to answer without your network 
> configuration. The manager have to listen on the right interface of 
> opensand core network.
> The core network have to interconnect the gw, st and sat instances of 
> Opensand.
> Be sure to relaunch opensand-daemon on each pc, to check the 
> configuration (dpkg-reconfigure opensand-daemon).
> You need only one instance of opensand manager (we usually use sat).
> For the state port, the best is to keep the default one.
>
> Anyway, we can see this more precisely next week when we met at CNES.
>
> Don't hesitate to precise your problems a little bit.
>
> Cordially,
>
> Emmanuel
>
> --------------------------------
> Emmanuel DUBOIS, CNES (Lagrange S28)
> (+33) 5 61 28 19 81
>
> -----Message d'origine-----
> De : bounces@xxxxxxxxxxxxx [mailto:bounces@xxxxxxxxxxxxx] De la part 
> de François Tuzet Envoyé : mardi 11 février 2014 18:52 À : Dubois 
> Emmanuel Objet : Enable to connect to state server
>
> Hello,
>
>  We are trying to install the opensand plateform for a project in our 
> school (ISAE-ENSICA) but when we launch opensand manager from the 
> gateway it shows us an error message "St1 enable to connect to state 
> server" and when we launch it from the ST1 it says  "GW enable to 
> connect to state server". So we can't start our project because the 3 
> entities are never available at the same time....
> It worked once but we didn't change the configuration parameters and 
> then it has stopped working...
> When we configure the daemons must we use the state port by default?
>
> Thanks in advance,
>
> François and Jonas
> --
> This message was sent from Launchpad by 
> =?utf-8?q?Fran=C3=A7ois_Tuzet?=
> (https://launchpad.net/~francois-tuzet)
> using the "Contact this team's admins" link on the OpenSand team page 
> (https://launchpad.net/~opensand).
> For more information see
> https://help.launchpad.net/YourAccount/ContactingPeople

--
FRANCOIS TUZET
Élève Ingénieur, 2ème année École nationale supérieure d'ingénieurs de constructions aéronautiques (ENSICA) Institut supérieur de l'aéronautique et de l'espace (ISAE) Membre du BDS
Tel: 06 81 75 39 15
Mail: francois.tuzet@xxxxxxx