openstack team mailing list archive

[Ahmed Al-Mehdi <ahmed@xxxxxxxxxx>]

Hi Anne,

Thank you for the explanation.  A few follow-up question:

1. Is the set of IP address mentioned by fixed_range distributed over all
the Compute Nodes. E.g., a VM on Compute Node1 would get an IP address
from this range.  Another VM instance on Compute Node2 would get an IP
address from this same range.  Is that right?

2. Pardon my ignorance, what does POC stand for?

3. br100 interface can be created on a Native Ubuntu server also, not
necessarily on VM in VirtualBox, right?

4. The br100 interface is only applicable to the Computer Node, not the
Controller Node, right?

5. The command to create the network for compute VMs - "nova-manage
network create Š." is executed on the Compute Node, right?

6. In my setup, one physical host will be the Controller Node, one
physical host is the Compute Node, and I might add another physical host
to be the Compute Node.  In this setup, what I the recommended setup for
public_interface?  Or does that depend on the number of NIC ports on the
physical host?

Thank you,
Ahmed.



On 10/3/12 8:26 PM, "Anne Gentle" <anne@xxxxxxxxxxxxx> wrote:

>Hi Ahmed -
>
>I have logged a doc bug to clear up this mismatch:
>https://bugs.launchpad.net/openstack-manuals/+bug/1061352.
>
>Appreciate you asking!
>
>Here's some explanation for each setting.
>fixed_range - fixed block of IP addresses handed out to VMs as they're
>provisioned. So these could be a 10.0.0.0/4 block if you want, or the
>192... block.
>public_interface - some say this needs to be a physical nic, but when
>you're running a POC on a VM on a laptop in VirtualBox for example, it
>can be br100. It's what DevStack defaults to. This setting indicates
>the interface nova-network uses to send the floating ip traffic on the
>correct network. So if you have nova-network on each compute node then
>yes, it belongs on the compute node.
>
>The Install/deploy guide walks through Flat DHCP as the network
>manager. If you use --network_bridge=br100 when you run the
>nova-manage network command, nova will set up the bridge for you. This
>example command uses 192.168.100.0/24 for the fixed range of IP
>addresses: 
>http://docs.openstack.org/trunk/openstack-compute/install/apt/content/comp
>ute-create-network.html
>
>Hope this helps.
>
>Others on the list, feel free to correct my explanations as needed!
>Thanks,
>Anne
>
>On Wed, Oct 3, 2012 at 6:46 PM, Ahmed Al-Mehdi <ahmed@xxxxxxxxxx> wrote:
>> Hello,
>>
>> I am following the steps in "OpenStack Install and Deploy ­ RedHat
>>Ubuntu"
>> (Folsom) to setup a Controller node.  The section "Configuring OpenStack
>> Compute" (
>> 
>>http://docs.openstack.org/trunk/openstack-compute/install/apt/content/com
>>pute-minimum-configuration-settings.html
>> )  gives a snippet of an example of the values of parameters in the
>> nova.conf file.
>>
>> The document first lists some common settings in nova.conf file.  I am
>> highlighting the following two which I am concerned about:
>>
>> fixed_range=192.168.100.0/24
>> public_interface=eth0
>>
>> The Document right after gives the whole content of a sample (usable)
>> nova.conf file for the Controller Node, in which the above settings are
>>set
>> as follows:
>>
>> fixed_range=10.0.0.0/24
>> public_interface=br100
>>
>> I am assuming "fixed_range=192.168.100.0/24" is the correct setting.
>> However, can someone please help as to the correct setting of
>> "public_interface".   And the same setting value would be applicable
>>for the
>> Compute Node, is that right?
>>
>> Thank you very much in advance.
>>
>> Regards,
>>
>> Ahmed.
>>
>>
>>
>> _______________________________________________
>> Mailing list: https://launchpad.net/~openstack
>> Post to     : openstack@xxxxxxxxxxxxxxxxxxx
>> Unsubscribe : https://launchpad.net/~openstack
>> More help   : https://help.launchpad.net/ListHelp
>>