sslug-teknik team mailing list archive
-
sslug-teknik team
-
Mailing list archive
-
Message #101998
Re: Hard disk problemer
Så vidt jeg kan se er der ikke sket ændringer i output fra smartctl. Men
jeg er også ret træt lige nu. Her er det nye output. Det gamle output
findes citeret længere nede i denne mail. Er der noget i det nye output
der får alarmklokkerne til at ringe?
root@medusa:~# smartctl -a /dev/sdb
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST9500325AS
Serial Number: 5VE15N1W
Firmware Version: 0001SDM1
User Capacity: 500.107.862.016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Wed Nov 23 02:05:14 2011 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has
ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 140) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 115 092 006 Pre-fail Always
- 89547351
3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 096 096 020 Old_age Always
- 5104
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always
- 1
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always
- 160152626
9 Power_On_Hours 0x0032 086 086 000 Old_age Always
- 12725
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 099 037 020 Old_age Always
- 2019
184 Unknown_Attribute 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always
- 623
188 Unknown_Attribute 0x0032 100 098 000 Old_age Always
- 3260
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 069 049 045 Old_age Always
- 31 (Lifetime Min/Max 31/34)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
- 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 186
193 Load_Cycle_Count 0x0032 093 093 000 Old_age Always
- 14915
194 Temperature_Celsius 0x0022 031 051 000 Old_age Always
- 31 (0 14 0 0)
195 Hardware_ECC_Recovered 0x001a 046 042 000 Old_age Always
- 89547351
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline
- 1
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
254 Unknown_Attribute 0x0032 100 100 000 Old_age Always
- 0
SMART Error Log Version: 1
ATA Error Count: 679 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 679 occurred at disk power-on lifetime: 12706 hours (529 days + 10
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 09:29:12.824 READ DMA EXT
27 00 00 00 00 00 e0 00 09:29:12.823 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 09:29:12.814 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 09:29:12.810 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 09:29:12.779 READ NATIVE MAX ADDRESS EXT
Error 678 occurred at disk power-on lifetime: 12706 hours (529 days + 10
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 09:29:10.209 READ DMA EXT
27 00 00 00 00 00 e0 00 09:29:10.207 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 09:29:10.198 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 09:29:10.190 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 09:29:10.162 READ NATIVE MAX ADDRESS EXT
Error 677 occurred at disk power-on lifetime: 12706 hours (529 days + 10
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 09:29:07.576 READ DMA EXT
27 00 00 00 00 00 e0 00 09:29:07.574 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 09:29:07.566 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 09:29:07.560 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 09:29:07.530 READ NATIVE MAX ADDRESS EXT
Error 676 occurred at disk power-on lifetime: 12706 hours (529 days + 10
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 09:29:04.956 READ DMA EXT
27 00 00 00 00 00 e0 00 09:29:04.955 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 09:29:04.946 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 09:29:04.941 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 09:29:04.910 READ NATIVE MAX ADDRESS EXT
Error 675 occurred at disk power-on lifetime: 12706 hours (529 days + 10
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 09:29:02.304 READ DMA EXT
27 00 00 00 00 00 e0 00 09:29:02.302 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 09:29:02.294 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 09:29:02.288 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 09:29:02.258 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
> root@medusa:/# smartctl -a /dev/sdb
> smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
> Home page is http://smartmontools.sourceforge.net/
>
> === START OF INFORMATION SECTION ===
> Device Model: ST9500325AS
> Serial Number: 5VE15N1W
> Firmware Version: 0001SDM1
> User Capacity: 500.107.862.016 bytes
> Device is: Not in smartctl database [for details use: -P showall]
> ATA Version is: 8
> ATA Standard is: ATA-8-ACS revision 4
> Local Time is: Fri Nov 18 19:08:55 2011 CET
> SMART support is: Available - device has SMART capability.
> SMART support is: Enabled
>
> === START OF READ SMART DATA SECTION ===
> SMART overall-health self-assessment test result: PASSED
>
> General SMART Values:
> Offline data collection status: (0x82) Offline data collection activity
> was completed without error.
> Auto Offline Data Collection:
> Enabled.
> Self-test execution status: ( 0) The previous self-test routine
> completed
> without error or no self-test has
> ever
> been run.
> Total time to complete Offline
> data collection: ( 0) seconds.
> Offline data collection
> capabilities: (0x7b) SMART execute Offline immediate.
> Auto Offline data collection
> on/off support.
> Suspend Offline collection upon
> new
> command.
> Offline surface scan supported.
> Self-test supported.
> Conveyance Self-test supported.
> Selective Self-test supported.
> SMART capabilities: (0x0003) Saves SMART data before entering
> power-saving mode.
> Supports SMART auto save timer.
> Error logging capability: (0x01) Error logging supported.
> General Purpose Logging supported.
> Short self-test routine
> recommended polling time: ( 1) minutes.
> Extended self-test routine
> recommended polling time: ( 140) minutes.
> Conveyance self-test routine
> recommended polling time: ( 2) minutes.
> SCT capabilities: (0x103b) SCT Status supported.
> SCT Feature Control supported.
> SCT Data Table supported.
>
> SMART Attributes Data Structure revision number: 10
> Vendor Specific SMART Attributes with Thresholds:
> ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
> WHEN_FAILED RAW_VALUE
> 1 Raw_Read_Error_Rate 0x000f 104 092 006 Pre-fail Always
> - 185181478
> 3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always
> - 0
> 4 Start_Stop_Count 0x0032 096 096 020 Old_age Always
> - 5100
> 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always
> - 1
> 7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always
> - 156172985
> 9 Power_On_Hours 0x0032 086 086 000 Old_age Always
> - 12645
> 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
> - 0
> 12 Power_Cycle_Count 0x0032 099 037 020 Old_age Always
> - 2015
> 184 Unknown_Attribute 0x0032 100 100 099 Old_age Always
> - 0
> 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always
> - 521
> 188 Unknown_Attribute 0x0032 100 098 000 Old_age Always
> - 3260
> 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
> - 0
> 190 Airflow_Temperature_Cel 0x0022 068 049 045 Old_age Always
> - 32 (Lifetime Min/Max 29/32)
> 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always
> - 0
> 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
> - 186
> 193 Load_Cycle_Count 0x0032 093 093 000 Old_age Always
> - 14906
> 194 Temperature_Celsius 0x0022 032 051 000 Old_age Always
> - 32 (0 14 0 0)
> 195 Hardware_ECC_Recovered 0x001a 046 042 000 Old_age Always
> - 185181478
> 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
> - 1
> 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline
> - 1
> 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
> - 0
> 254 Unknown_Attribute 0x0032 100 100 000 Old_age Always
> - 0
>
> SMART Error Log Version: 1
> ATA Error Count: 577 (device log contains only the most recent five
> errors)
> CR = Command Register [HEX]
> FR = Features Register [HEX]
> SC = Sector Count Register [HEX]
> SN = Sector Number Register [HEX]
> CL = Cylinder Low Register [HEX]
> CH = Cylinder High Register [HEX]
> DH = Device/Head Register [HEX]
> DC = Device Command Register [HEX]
> ER = Error register [HEX]
> ST = Status register [HEX]
> Powered_Up_Time is measured from power on, and printed as
> DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
> SS=sec, and sss=millisec. It "wraps" after 49.710 days.
>
> Error 577 occurred at disk power-on lifetime: 12642 hours (526 days + 18
> hours)
> When the command that caused the error occurred, the device was active
> or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 00 ff ff ff ef 00 00:12:36.343 READ DMA EXT
> 27 00 00 00 00 00 e0 00 00:12:36.341 READ NATIVE MAX ADDRESS EXT
> ec 00 00 00 00 00 a0 00 00:12:36.333 IDENTIFY DEVICE
> ef 03 46 00 00 00 a0 00 00:12:36.326 SET FEATURES [Set transfer
> mode]
> 27 00 00 00 00 00 e0 00 00:12:36.293 READ NATIVE MAX ADDRESS EXT
>
> Error 576 occurred at disk power-on lifetime: 12642 hours (526 days + 18
> hours)
> When the command that caused the error occurred, the device was active
> or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 00 ff ff ff ef 00 00:12:33.734 READ DMA EXT
> 27 00 00 00 00 00 e0 00 00:12:33.733 READ NATIVE MAX ADDRESS EXT
> ec 00 00 00 00 00 a0 00 00:12:33.724 IDENTIFY DEVICE
> ef 03 46 00 00 00 a0 00 00:12:33.718 SET FEATURES [Set transfer
> mode]
> 27 00 00 00 00 00 e0 00 00:12:33.689 READ NATIVE MAX ADDRESS EXT
>
> Error 575 occurred at disk power-on lifetime: 12642 hours (526 days + 18
> hours)
> When the command that caused the error occurred, the device was active
> or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 00 ff ff ff ef 00 00:12:31.113 READ DMA EXT
> 27 00 00 00 00 00 e0 00 00:12:31.112 READ NATIVE MAX ADDRESS EXT
> ec 00 00 00 00 00 a0 00 00:12:31.104 IDENTIFY DEVICE
> ef 03 46 00 00 00 a0 00 00:12:31.098 SET FEATURES [Set transfer
> mode]
> 27 00 00 00 00 00 e0 00 00:12:31.068 READ NATIVE MAX ADDRESS EXT
>
> Error 574 occurred at disk power-on lifetime: 12642 hours (526 days + 18
> hours)
> When the command that caused the error occurred, the device was active
> or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 00 ff ff ff ef 00 00:12:28.497 READ DMA EXT
> 27 00 00 00 00 00 e0 00 00:12:28.495 READ NATIVE MAX ADDRESS EXT
> ec 00 00 00 00 00 a0 00 00:12:28.487 IDENTIFY DEVICE
> ef 03 46 00 00 00 a0 00 00:12:28.479 SET FEATURES [Set transfer
> mode]
> 27 00 00 00 00 00 e0 00 00:12:28.447 READ NATIVE MAX ADDRESS EXT
>
> Error 573 occurred at disk power-on lifetime: 12642 hours (526 days + 18
> hours)
> When the command that caused the error occurred, the device was active
> or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 00 ff ff ff ef 00 00:12:25.908 READ DMA EXT
> 27 00 00 00 00 00 e0 00 00:12:25.906 READ NATIVE MAX ADDRESS EXT
> ec 00 00 00 00 00 a0 00 00:12:25.898 IDENTIFY DEVICE
> ef 03 46 00 00 00 a0 00 00:12:25.893 SET FEATURES [Set transfer
> mode]
> 27 00 00 00 00 00 e0 00 00:12:25.862 READ NATIVE MAX ADDRESS EXT
>
> SMART Self-test log structure revision number 1
> No self-tests have been logged. [To run self-tests, use: smartctl -t]
>
>
> SMART Selective self-test log data structure revision number 1
> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
> 1 0 0 Not_testing
> 2 0 0 Not_testing
> 3 0 0 Not_testing
> 4 0 0 Not_testing
> 5 0 0 Not_testing
> Selective self-test flags (0x0):
> After scanning selected spans, do NOT read-scan remainder of disk.
> If Selective self-test is pending on power-up, resume after 0 minute
> delay.
>
>
>
>
>
References
