sslug-teknik team mailing list archive

[Jan Vittrup Hansen <Jan.Vittrup@xxxxxxxxx>]

    Hej,

Er der nogle successhistorier med tapedrev ved parallel porten? 
(specifikt HP Colorado 10/20GB (Travan))
Kan det passe at jeg skal benytte ftape/zftape? I så fald kan jeg da 
nøjes med den version 3,
der følger med min redhat 6.1 kerne 2.2.12-20 - den klager nemlig over 
min enhed ikke er korrekt konfigureret når jeg benytter "mt":

/sbin/lsmod

Module                  Size  Used by
parport_probe           2980   0  (autoclean)
parport_pc              5620   1  (autoclean)
lp                      4476   0  (autoclean)
parport                 7124   1  (autoclean) [parport_probe parport_pc lp]
nfsd                  144060   8  (autoclean)
lockd                  30984   0  (autoclean) [nfsd]
sunrpc                 52516   0  (autoclean) [nfsd lockd]
rtl8139                12188   1  (autoclean)

/sbin/lsmod

Module Size Used by
zftape 59084 -1 (unused)
ftape 105844 0 [zftape]
parport_probe 2980 0 (autoclean)
parport_pc 5620 1 (autoclean)
lp 4476 0 (autoclean)
parport 7124 1 (autoclean) [parport_probe parport_pc lp]
nfsd 144060 8 (autoclean)
lockd 30984 0 (autoclean) [nfsd]
sunrpc 52516 0 (autoclean) [nfsd lockd]
rtl8139                12188   1  (autoclean)

mt -f /dev/qft0 status
/dev/qft0: Device not configured

tail -40  /var/log/messages
Feb  3 17:22:32 nulle kernel: ftape v3.04d 25/11/97
Feb  3 17:22:32 nulle kernel: (c) 1993-1996 Bas Laarhoven (bas@xxxxxxxx)
Feb  3 17:22:32 nulle kernel: (c) 1995-1996 Kai Harrekilde-Petersen 
(khp@xxxxxxxxxxxxx)
Feb  3 17:22:32 nulle kernel: (c) 1996-1997 Claus-Justus Heine 
(claus@xxxxxxxxxxxxxxxxxxxxxxxx)
Feb  3 17:22:32 nulle kernel: QIC-117 driver for QIC-40/80/3010/3020 
floppy tape drives
Feb  3 17:22:32 nulle kernel: Compiled for Linux version 2.2.12-20 with 
versioned symbols
Feb  3 17:22:32 nulle kernel: [000] ftape-init.c (ftape_init) - 
installing QIC-117 floppy tape hardware drive ... .
Feb  3 17:22:32 nulle kernel: [001] ftape-init.c (ftape_init) - 
ftape_init @ 0xc286604c.
Feb  3 17:22:32 nulle kernel: [002]   ftape-buffer.c (add_one_buffer) - 
buffer nr #1 @ c18494a0, dma area @ c0720000.
Feb  3 17:22:32 nulle kernel: [003]   ftape-buffer.c (add_one_buffer) - 
buffer nr #2 @ c0481dc0, dma area @ c0588000.
Feb  3 17:22:32 nulle kernel: [004]   ftape-buffer.c (add_one_buffer) - 
buffer nr #3 @ c124ba40, dma area @ c0428000.
Feb  3 17:22:32 nulle kernel: [005]   ftape-calibr.c (time_inb) - inb() 
duration: 637 nsec.
Feb  3 17:22:32 nulle kernel: [006]  ftape-calibr.c (ftape_calibrate) - 
TC for `ftape_udelay()' = 834 nsec (at 10239 counts).
Feb  3 17:22:32 nulle kernel: [007]  ftape-calibr.c (ftape_calibrate) - 
TC for `fdc_wait()' = 1721 nsec (at 5119 counts).
Feb  3 17:22:32 nulle kernel: zftape for ftape v3.04d 25/11/97
Feb  3 17:22:32 nulle kernel: (c) 1996, 1997 Claus-Justus Heine 
(claus@xxxxxxxxxxxxxxxxxxxxxxxx)
Feb  3 17:22:32 nulle kernel: vfs interface for ftape floppy tape driver.
Feb  3 17:22:32 nulle kernel: Support for QIC-113 compatible volume 
table, dynamic memory allocation
Feb  3 17:22:32 nulle kernel: and builtin compression (lzrw3 algorithm).
Feb  3 17:22:32 nulle kernel: Compiled for Linux version 2.2.12-20 with 
versioned symbols
Feb  3 17:22:32 nulle kernel: [008] zftape-init.c (zft_init) - zft_init 
@ 0xc288acb0.
Feb  3 17:22:32 nulle kernel: [009] zftape-init.c (zft_init) - 
installing zftape VFS interface for ftape driver ....
Feb  3 17:23:16 nulle kernel: [010]     fdc-io.c (fdc_config) - fdc 
base: 0x3f0, irq: 6, dma: 2.
Feb  3 17:23:16 nulle kernel: [011]     fdc-io.c (fdc_probe) - Type 
82077AA compatible FDC found.
Feb  3 17:23:22 nulle kernel: [012]    ftape-ctl.c 
(ftape_activate_drive) - no tape drive found !.
Feb  3 17:23:22 nulle kernel: [013]   ftape-ctl.c 
(ftape_enable_R7ec0d5d4) - 
ftape_activate_drive(&ftape_status.fti_drive_type) failed: -19.
Feb  3 17:23:22 nulle kernel: [014]  zftape-ctl.c (_zft_open) - 
ftape_enable failed: -19.
Feb  3 17:23:22 nulle kernel: [015] zftape-init.c (zft_open) - 
_ftape_open failed.

Den har ganske ret - der intet tape på FDC'en den skulle gerne teste den 
parallelle port.
Jeg ingen options på mine moduler - kerne docs'ene handler om IDE 
controllere, nævner ikke parallelle,
Ftape-HOWTO'en virker noget tynd hvad gælder parallelle ting - og kudzu 
finder intet.

Nogle gode ideer til hvordan jeg kommer videre?

 mvh, Jan...