sslug-teknik team mailing list archive

[Carl Andersen <fruegade@xxxxxxxxxxxxxx>]

Peter Makholm wrote:

> Hvordan er din lilo sat op?
> 
> Noget kunne tyde på at du booter den kerne der følger med mandrake og
> så bare mounter den rette partition som root, når du bruger
> Debian. Dette er der i sig selv ikke noget galt i. Jeg ville til
> enhver tid nøjes med at oversætte kerner det ene sted, med mindre den
> ene distribution havde særlige krav med hensyn til kernen.

Jeg vil først sige, jeg er nybegynder i kernekomplering, jeg har sidst
kørt lilo i debian. Jeg har ikke lavet kernekompelerig i mandrake, og
vil heller ikke gøre dette 

> Hvordan ser dine lilo.conf'er ud og hvor har du sidst kørt lilo? 

Min lilo.conf i mandrake ser sådan ud

boot=/dev/sda
map=/boot/map
install=/boot/boot.b
vga=normal
default=linux
keytable=/boot/dk-latin1.klt
lba32
prompt
timeout=150
message=/boot/message
menu-scheme=wb:bw:wb:bw
image=/boot/vmlinuz
	label=linux
	root=/dev/sda6
	initrd=/boot/initrd.img
	read-only
image=/boot/vmlinuz
	label=debian
	root=/dev/sda8
	initrd=/boot/initrd.img
	read-only
image=/boot/vmlinuz
	label=failsafe
	root=/dev/sda6
	initrd=/boot/initrd.img
	append=" failsafe"
	read-only
other=/dev/fd0
	label=floppy
	unsafe


Min lilo.conf i debian ser sådan ud

/etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------       `install-mbr(8)', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run `lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
lba32

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/sda8

# Specifies the device that should be mounted as root. (`/')
#
root=/dev/sda8

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
#
install=/boot/boot.b

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
#	prompt
#	single-key
#	delay=100
#	timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask,
<mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""

# Boot up Linux by default.
#
default=Linux

image=/vmlinuz
	label=Linux
	read-only
#	restricted
#	alias=1

image=/vmlinuz.old
	label=LinuxOLD
	read-only
	optional
#	restricted
#	alias=2

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#	label=HURD
#	restricted
#	alias=3


Det kunne jo tyde på at min custom kerne ikke er der?, jeg kan boote op
med disketten der blev lavet ved kernekompeleringen, Men jeg vil gerne
kunne boote op fra mandraks lilo, har du nogen ide om hvordan det kan
gøres

mvh	Carl  Andersen