sslug-teknik team mailing list archive

["Kim Hermansen" <k.hermansen@xxxxxxxxxxxxxxxx>]

----- Original Message -----
From: <Kristian.Hogh@xxxxxx>
To: <sslug-teknik@xxxxxxxx>
Sent: Friday, April 12, 2002 10:15 AM
Subject: RE: [TEKNIK] Promise Ultra 133 TX2 -> Hvor er min disk???


> > -----Original Message-----
> > From: Kim Hermansen [mailto:k.hermansen@xxxxxxxxxxxxxxxx]
> >
> > Jeg sidder lige med et forhåbentligt lille problem.
> > Da jeg nu løb tør for ide pladser har jeg smidt en
> > Promise Ultra 133 TX2 controller i maskineriet.
> > På denne har jeg så sat en 120 GB disk som så jo
> > naturligvis gerne skulle formateres og skrives med i fstab.
> > Problemet er at jeg ikke kan finde min disk, jeg havde
> > forventet at den ville være der under /dev/hde
> > (hda,b,c,d er brugt) men da jeg glad skrev
> > fdisk /dev/hde lader det til at der ikke er nogen disk.
> > Er der nogen der har et bud på hvad der går galt??
>
> Finder linux controlleren/drevet under boot?
> Prøv "dmesg | less"?
>
> /Kristian Høgh.
>
>
>
Det ser  ikke ud til at det bliver fundet som det skal, men jeg må tilstå at
jeg
er lidt på herrens mark med hensyn til hvor det går galt.

Men for at du lige kan se output fra dmesg har jeg klippet den ind herunder

######################################################
Linux version 2.4.7-10 (bhcompile@xxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version
2.96 20000731 (Red Hat Linux 7.1 2.96-98)) #1 Thu Sep 6 17:21:28 EDT 2001

BIOS-provided physical RAM map:

BIOS-e820: 0000000000000000 - 000000000009e800 (usable)

BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)

BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)

BIOS-e820: 0000000000100000 - 000000000fffc000 (usable)

BIOS-e820: 000000000fffc000 - 000000000ffff000 (ACPI data)

BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)

BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)

On node 0 totalpages: 65532

zone(0): 4096 pages.

zone(1): 61436 pages.

zone(2): 0 pages.

Kernel command line: auto BOOT_IMAGE=linux ro root=305
BOOT_FILE=/boot/vmlinuz-2.4.7-10

Initializing CPU#0

Detected 350.789 MHz processor.

Console: colour VGA+ 80x25

Calibrating delay loop... 699.59 BogoMIPS

Memory: 253076k/262128k available (1280k kernel code, 6736k reserved, 90k
data, 216k init, 0k highmem)

Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)

Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)

Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)

Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)

Page-cache hash table entries: 65536 (order: 7, 524288 bytes)

CPU: Before vendor init, caps: 008001bf 808009bf 00000000, vendor = 2

CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)

CPU: After vendor init, caps: 008001bf 808009bf 00000000 00000000

CPU: After generic, caps: 008001bf 808009bf 00000000 00000000

CPU: Common caps: 008001bf 808009bf 00000000 00000000

CPU: AMD-K6(tm) 3D processor stepping 00

Checking 'hlt' instruction... OK.

Checking for popad bug... OK.

POSIX conformance testing by UNIFIX

mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx)

mtrr: detected mtrr type: none

PCI: PCI BIOS revision 2.10 entry at 0xf0720, last bus=1

PCI: Using configuration type 1

PCI: Probing PCI hardware

Unknown bridge resource 0: assuming transparent

PCI: Using IRQ router ALI [10b9/1533] at 00:07.0

isapnp: Scanning for PnP cards...

isapnp: No Plug & Play device found

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Simple Boot Flag extension found and enabled.

apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)

Starting kswapd v1.8

VFS: Diskquotas version dquot_6.5.0 initialized

pty: 512 Unix98 ptys configured

Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled

ttyS00 at 0x03f8 (irq = 4) is a 16550A

ttyS01 at 0x02f8 (irq = 3) is a 16550A

Real Time Clock Driver v1.10d

block: queued sectors max/low 168013kB/56004kB, 512 slots per queue

RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize

Uniform Multi-Platform E-IDE driver Revision: 6.31

ide: Assuming 33MHz PCI bus speed for PIO modes; override with idebus=xx

ALI15X3: IDE controller on PCI bus 00 dev 78

PCI: No IRQ known for interrupt pin A of device 00:0f.0. Please try using
pci=biosirq.

ALI15X3: chipset revision 193

ALI15X3: not 100% native mode: will probe irqs later

ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:DMA, hdb:DMA

ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:DMA, hdd:DMA

hda: FUJITSU MPC3043AT, ATA DISK drive

hdb: IBM-DHEA-36480, ATA DISK drive

ide: Assuming 33MHz PCI bus speed for PIO modes; override with idebus=xx

hdc: MAXTOR 4K080H4, ATA DISK drive

hdd: IC35L020AVER07-0, ATA DISK drive

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

ide1 at 0x170-0x177,0x376 on irq 15

hda: 8448300 sectors (4326 MB), CHS=525/255/63, UDMA(33)

hdb: 12692736 sectors (6499 MB) w/476KiB Cache, CHS=790/255/63, UDMA(33)

hdc: 156301487 sectors (80026 MB) w/2000KiB Cache, CHS=155060/16/63,
UDMA(33)

hdd: 40188960 sectors (20577 MB) w/1916KiB Cache, CHS=39870/16/63, UDMA(33)

ide-floppy driver 0.97

Partition check:

hda: hda1 hda2 hda3 hda4 < hda5 >

hdb: hdb1 hdb2

hdc: [PTBL] [9729/255/63] hdc1

hdd: hdd1

Floppy drive(s): fd0 is 1.44M

FDC 0 is a post-1991 82077

ide-floppy driver 0.97

md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27

md: Autodetecting RAID arrays.

md: autorun ...

md: ... autorun DONE.

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

IP: routing cache hash table of 2048 buckets, 16Kbytes

TCP: Hash tables configured (established 16384 bind 16384)

Linux IP multicast router 0.06 plus PIM-SM

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

RAMDISK: Compressed image found at block 0

Freeing initrd memory: 437k freed

VFS: Mounted root (ext2 filesystem).

SCSI subsystem driver Revision: 1.00

Journalled Block Device driver loaded

kjournald starting. Commit interval 5 seconds

EXT3-fs: mounted filesystem with ordered data mode.

Freeing unused kernel memory: 216k freed

Adding Swap: 522072k swap-space (priority -1)

EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,5), internal journal

kjournald starting. Commit interval 5 seconds

EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,1), internal journal

EXT3-fs: mounted filesystem with ordered data mode.

kjournald starting. Commit interval 5 seconds

EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide1(22,65), internal journal

EXT3-fs: mounted filesystem with ordered data mode.

kjournald starting. Commit interval 5 seconds

EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,2), internal journal

EXT3-fs: mounted filesystem with ordered data mode.

kjournald starting. Commit interval 5 seconds

EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,3), internal journal

EXT3-fs: mounted filesystem with ordered data mode.

kjournald starting. Commit interval 5 seconds

EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,66), internal journal

EXT3-fs: mounted filesystem with ordered data mode.

kjournald starting. Commit interval 5 seconds

EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide1(22,1), internal journal

EXT3-fs: mounted filesystem with ordered data mode.

0x378: FIFO is 16 bytes

0x378: writeIntrThreshold is 7

0x378: readIntrThreshold is 7

0x378: PWord is 8 bits

0x378: Interrupts are ISA-Pulses

0x378: ECP port cfgA=0x10 cfgB=0x4b

0x378: ECP settings irq=7 dma=3

parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,COMPAT,ECP]

parport0: irq 7 detected

parport0: cpp_daisy: aa5500ff(38)

parport0: assign_addrs: aa5500ff(38)

parport0: cpp_daisy: aa5500ff(38)

parport0: assign_addrs: aa5500ff(38)

ip_conntrack (2047 buckets, 16376 max)

via-rhine.c:v1.10-LK1.1.10 07/12/2001 Written by Donald Becker

http://www.scyld.com/network/via-rhine.html

PCI: Found IRQ 10 for device 00:0d.0

via-rhine: reset did not complete in 10 ms.

eth0: VIA VT3043 Rhine at 0xb000, 00:50:ba:09:98:e2, IRQ 10.

eth0: MII PHY found at address 8, status 0x782d advertising 05e1 Link 45e1.

eth0: Setting full-duplex based on MII #8 link partner capability of 45e1.

######################################################