sslug-teknik team mailing list archive

[Jesper Krogh <jesper@xxxxxxxx>]

Jeg er 99% sikker på at dette er et kerne 2.6-relateret problem, da jeg
ikke bed mærke i det før jeg opdaterede. 

Jeg kører p.t. på 2.6.7 kernen fra Debian Testing og når maskinen
booter, så tager det lang tid at loade modulerne uhci (Er vistnok USB)
og pcmcia

Er der nogen måde at "speede" denne modul-load op på? Da det er en
bærbar, så er det jo rarest at have en relativ kort boot-up tid. 

dmesg klippet ind her:

-----------------
floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
pnp: Device 00:17 activated.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 830M Chipset.
agpgart: Maximum main memory to use for agp memory: 321M
agpgart: AGP aperture is 256M @ 0xd0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0.PCI1 _HPP fail=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PCI1 OSHP fails=0x5
pciehp: acpi_pciehprm:   Slot sun(1) at s:b:d:f=0x00:02:03:00
pciehp: acpi_pciehprm:\_SB_.PCI0.PCI1 _HPP fail=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0.PCI1 OSHP fails=0x5
pciehp: acpi_pciehprm:   Slot sun(2) at s:b:d:f=0x00:02:03:01
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
shpchp: acpi_shpchprm:\_SB_.PCI0.PCI1 _HPP fail=0x5
shpchp: acpi_pciehprm:\_SB_.PCI0.PCI1 OSHP fails=0x5
shpchp: acpi_shpchprm:   Slot sun(1) at s:b:d:f=0x00:02:03:00
shpchp: acpi_shpchprm:\_SB_.PCI0.PCI1 _HPP fail=0x5
shpchp: acpi_pciehprm:\_SB_.PCI0.PCI1 OSHP fails=0x5
shpchp: acpi_shpchprm:   Slot sun(2) at s:b:d:f=0x00:02:03:01
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1d.0: Intel Corp. 82801CA/CAM USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 00001800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: Intel Corp. 82801CA/CAM USB (Hub #2)
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 11, io base 00001820
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: Intel Corp. 82801CA/CAM USB (Hub #3)
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 11, io base 00001840
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hw_random hardware driver 1.0.0 loaded
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:02:03.0 [1014:0185]
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
Yenta: CardBus bridge found at 0000:02:03.1 [1014:0185]
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
---------------

Jeg _skal_ have pcmcia loaded, og helst også USB, så man ikke skal sidde 
og fedte med det ad-hoc.

Hvor hurtigt starter jeres 2.6-systemer op når USB/pcmcia skal startes? 

Der benyttes "udev" på maskinen, men det tror jeg nu ikke har nogen 
betydning i den sammenhæng. 


-- 
./Jesper Krogh, jesper@xxxxxxxx
Jabber ID: jesper@xxxxxxxxxxxx