sslug-teknik team mailing list archive

[Atte André Jensen <atte@xxxxxxxxxxxxxx>]

Hejsa

Jeg vil gerne kunne sync'e min palm (Sony Clié PEG-TJ25/E1, palm os 
5.2.1) med min laptop som kører debian/unstable kerne 2.6.9. Jeg synes 
jeg har prøvet alt, men Det Virker Ikke (TM).

Fx:
[root@aarhus ~]$ cat /dev/ttyS0
cat: /dev/ttyS0: Input/output error

og irdadump kommer ikke med noget output overhovedet.

Mid bedste bud på en del af problemet er at ttyS0 er brugt i forvejen, 
se dmesg nederst. Ellers er jeg ret blank for hvordan jeg kommer videre. 
Er der nogen her som syncer deres palm over IR under linux? Osse under 
kerne 2.6.x?

Her er lidt fra min kernekonfiguration:

[atte@aarhus linux]$ grep CONFIG_IR .config
CONFIG_IRDA=m
CONFIG_IRLAN=m
CONFIG_IRNET=m
CONFIG_IRCOMM=m
CONFIG_IRDA_ULTRA=y
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
CONFIG_IRDA_DEBUG=y
CONFIG_IRTTY_SIR=m
CONFIG_IRPORT_SIR=m

Og jeg har følgende modulter loadet (ircomm_tty har jeg loadet i hånden...):
[atte@aarhus linux]$ lsmod
Module                  Size  Used by
ircomm_tty             33544  0
ircomm                 18308  1 ircomm_tty
irtty_sir               7680  2
sir_dev                15020  1 irtty_sir
irda                  175040  4 ircomm_tty,ircomm,irtty_sir,sir_dev
<snip ndiswrapper + lyd>

Desuden:
[atte@aarhus ~]$ dmesg | grep -v TouchPad
20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Uncovering SIS962 that hid as a SIS503 (compatible=1)
Enabling SiS 96x SMBus.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Embedded Controller [EC0] (gpe 11)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 *11 12 14 15)
SCSI subsystem initialized
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:02.3[B] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:02.6[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:03.2[C] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
NTFS driver 2.1.20 [Flags: R/W].
Initializing Cryptographic API
ACPI: AC Adapter [AC0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies 
Inc Radeon R250 Lf [Radeon Mob
ility 9000 M9]
ipmi message handler version v33
ipmi device interface version v33
IPMI Watchdog: driver version v33
i8042.c: Detected active multiplexing controller, rev 1.0.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 8250
ACPI: PCI interrupt 0000:00:02.6[C] -> GSI 10 (level, low) -> IRQ 10
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
sis900.c: v1.08.07 11/02/2003
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: Realtek RTL8201 PHY transceiver found at address 1.
eth0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xcc00, IRQ 10, 00:a0:cc:dc:84:8a.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
    ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: HITACHI_DK23EA-30, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/2048KiB Cache, CHS=58140/16/63, UDMA(33)
hda: cache flushes supported
 hda: hda1 hda2 hda3
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX 
as device
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
  Vendor: QSI       Model: CDRW/DVD SBW-241  Rev: VU02
  Type:   CD-ROM                             ANSI SCSI revision: 02
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 5
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:08.0 [1584:3000]
Yenta: ISA IRQ mask 0x0088, PCI irq 11
Socket status: 30000007
Databook TCIC-2 PCMCIA probe: not found.
ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:03.3: Silicon Integrated Systems [SiS] USB 2.0 Controller
ehci_hcd 0000:00:03.3: irq 11, pci mem e0806000
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:03.0: Silicon Integrated Systems [SiS] USB 1.0 Controller
ohci_hcd 0000:00:03.0: irq 10, pci mem e0828000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:03.1: Silicon Integrated Systems [SiS] USB 1.0 
Controller (#2)
ohci_hcd 0000:00:03.1: irq 10, pci mem e082a000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:03.2[C] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:03.2: Silicon Integrated Systems [SiS] USB 1.0 
Controller (#3)
ohci_hcd 0000:00:03.2: irq 5, pci mem e082c000
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.2
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for 
Handspring Visor / Palm OS
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony 
Clie 3.5
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony 
Clie 5.0
usbcore: registered new driver visor
drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver v2.1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
Synaptics Touchpad, model: 1
 Firmware: 4.1
 Sensor: 8
 new absolute packet format
input: PC Speaker
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ACPI: (supports S0 S3 S4 S5)
ACPI wakeup devices:
PCI0 PS2M PS2K  EC0  LID USB1 USB2 USB3 USB4 S139  LAN  MDM  AUD SLPB
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 160k freed
hdc: CHECK for good STATUS
Adding 489972k swap on /dev/hda3.  Priority:-1 extents:1
EXT3 FS on hda1, internal journal
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 10 (level, low) -> IRQ 10
intel8x0_measure_ac97_clock: measured 48991 usecs
intel8x0: clocking to 48000
usbcore: registered new driver snd-usb-audio
ndiswrapper version 0.12 loaded (preempt=yes,smp=no)
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 5 (level, low) -> IRQ 5
ndiswrapper: using irq 5
wlan0: ndiswrapper ethernet device 00:90:4b:24:09:03 using driver bcmwl5
wlan0: encryption modes supported: WEP, WPA with TKIP
ndiswrapper: driver bcmwl5 (Broadcom,06/13/2003, 3.20.23.0) added
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: Media Link Off
irda_init()
NET: Registered protocol family 23
sirdev_get_instance - ttyS0
irtty_open - ttyS0: irda line discipline opened
irlap_change_speed(), setting speed to 9600
[drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:radeon_unlock] *ERROR* Process 2363 using kernel context 0
Stopping tasks: ========================================================|
Back to C!
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 10 (level, low) -> IRQ 10
eth0: Media Link Off
ndiswrapper: using irq 5
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
    ACPI-0286: *** Error: No installed handler for fixed event [00000000]
Restarting tasks... done
IrCOMM protocol (Dag Brattli)



--
peace, love & harmony
Atte

http://www.atte.dk