sslug-teknik team mailing list archive
-
sslug-teknik team
-
Mailing list archive
-
Message #85225
knoppmyth pvr-350 tuner problem
Hej Drenge & Piger
Min kone er blevet træt af ,jeg sidder og bruger så meget tid på linux.
efter jeg købt et hauppauge pvr 350 tuner kort. valget af kortet er
grundet hw ind/de kodning af signal ,så cpu'en ikke skal over arbejde.
Jeg har installeret KnoppMythR5A22 på en amd 1600 mzh.
Har afprøvet på hardwaren under M$ xp pro,virkede fint,men knoppmyth
har bare det der skal til for en hiend harddisk recorder ;-)
Så jeg spørger her ,om der er nogle ,der har løsnings forslag ,til
flg. problem.
jeg kan ikke få tuner modulet til at grappe signalet.
jeg har søgt på internette i en hel uge for at finde en løsning.
jeg har set på /prøvet mange modul opsætninger fra tilsvarende systemer
med pvr-350 kortet ,og har ikke kunne gennemskue om det er frimware /
driveren. eller opsætningen der gør at tuner ikke loader ordenligt.
grap af lsmod
---------------------
sg 30496 0
ehci_hcd 31368 0
shpchp 91524 0
pci_hotplug 27716 1 shpchp
sis_agp 8068 1
pcspkr 5344 0
cx8800 28044 0
cx88xx 53024 1 cx8800
ir_common 8836 1 cx88xx
lirc_i2c 10372 1
lirc_dev 14852 1 lirc_i2c
ipv6 240128 14
ttusb_dec 22028 0
ttusbdecfe 4992 1 ttusb_dec
dvb_ttusb_budget 30364 0
cx22700 7044 1 dvb_ttusb_budget
budget_av 14464 0
tda10021 7684 1 budget_av
budget_ci 12288 0
budget 10752 0
s5h1420 9860 1 budget
budget_core 8836 3 budget_av,budget_ci,budget
dvb_ttpci 88004 0
l64781 8452 2 budget,dvb_ttpci
tda8083 7044 3 dvb_ttusb_budget,budget,dvb_ttpci
stv0297 9216 1 dvb_ttpci
sp8870 8588 1 dvb_ttpci
ttpci_eeprom 4352 2 budget_core,dvb_ttpci
saa7146_vv 44672 2 budget_av,dvb_ttpci
saa7146 16520 6
budget_av,budget_ci,budget,budget_core,dvb_ttpci,saa7146_vv
mt312 8964 0
tda1004x 14724 3 dvb_ttusb_budget,budget_av,budget_ci
ves1820 7172 3 dvb_ttusb_budget,budget,dvb_ttpci
stv0299 11912 5
dvb_ttusb_budget,budget_av,budget_ci,budget,dvb_ttpci
ves1x93 7940 2 budget,dvb_ttpci
dvb_bt8xx 11780 0
nxt6000 8580 1 dvb_bt8xx
mt352 7812 1 dvb_bt8xx
sp887x 8836 1 dvb_bt8xx
dst_ca 14848 1 dvb_bt8xx
or51211 11140 1 dvb_bt8xx
dst 19332 2 dvb_bt8xx,dst_ca
bt878 10200 2 dvb_bt8xx,dst
cx24110 8836 1 dvb_bt8xx
dvb_core 75304 9
ttusb_dec,dvb_ttusb_budget,budget_av,budget_ci,budget,budget_core,dvb_ttpci,dvb_bt8xx,dst_ca
bttv 154000 2 dvb_bt8xx,bt878
btcx_risc 5896 3 cx8800,cx88xx,bttv
video_buf 18948 4 cx8800,cx88xx,saa7146_vv,bttv
v4l2_common 6784 3 cx8800,saa7146_vv,bttv
v4l1_compat 14980 2 cx8800,saa7146_vv
skge 34832 0
autofs4 17796 1
af_packet 20616 2
snd_mixer_oss 17536 0
snd_intel8x0 29632 0
snd_ac97_codec 76412 1 snd_intel8x0
snd_pcm 78084 2 snd_intel8x0,snd_ac97_codec
snd_timer 22532 1 snd_pcm
snd_page_alloc 10120 2 snd_intel8x0,snd_pcm
snd 47972 5
snd_mixer_oss,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 9312 1 snd
agpgart 30416 1 sis_agp
tda9887 14352 0
saa7127 12564 0
tveeprom 14380 2 cx88xx,bttv
ivtv 206228 2
saa7115 14608 0 <--------------------
msp3400 27056 0 Her mangler modulet at loade ordenligt
tuner 24352 0 <--------------------
i2c_algo_bit 10504 3 cx88xx,bttv,ivtv
videodev 9472 5 cx8800,cx88xx,saa7146_vv,bttv,ivtv
3c59x 40360 0
sis900 20352 0
mii 6400 2 3c59x,sis900
i2c_sis96x 6788 0
i2c_core 19200 37
cx88xx,lirc_i2c,dvb_ttusb_budget,cx22700,budget_av,tda10021,budget_ci,budget,s5h1420,budget_core,dvb_ttpci,l64781,tda8083,stv0297,sp8870,ttpci_eeprom,mt312,tda1004x,ves1820,stv0299,ves1x93,dvb_bt8xx,nxt6000,mt352,sp887x,or51211,dst,cx24110,bttv,tda9887,saa7127,tveeprom,saa7115,msp3400,tuner,i2c_algo_bit,i2c_sis96x
parport_pc 37444 0
parport 32456 1 parport_pc
8250 22660 0
serial_core 20096 1 8250
pcmcia 32808 0
firmware_class 9728 12
ttusb_dec,dvb_ttusb_budget,budget_av,budget_ci,dvb_ttpci,sp8870,tda1004x,dvb_bt8xx,sp887x,or51211,bttv,pcmcia
yenta_socket 22924 0
rsrc_nonstatic 12800 1 yenta_socket
pcmcia_core 36888 3 pcmcia,yenta_socket,rsrc_nonstatic
video 16260 0
thermal 12936 0
processor 23016 1 thermal
ohci1394 32436 0
ieee1394 299352 1 ohci1394
usb_storage 60608 0
ohci_hcd 20484 0
uhci_hcd 31760 0
usbcore 103932 6
ehci_hcd,ttusb_dec,dvb_ttusb_budget,usb_storage,ohci_hcd,uhci_hcd
tmscsim 22976 0
BusLogic 76564 0
tsdev 7872 0
evdev 9088 0
------------------------------------
grap af dmesg
Linux version 2.6.13.2-chw-3 (root@xxxxxxxxxxxxxxxxxx) (gcc version
3.3.6 (Debian 1:3.3.6-5)) #1 SMP Wed Sep 21 08:15:54 PDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bff0000 (usable)
BIOS-e820: 000000001bff0000 - 000000001bff8000 (ACPI data)
BIOS-e820: 000000001bff8000 - 000000001c000000 (ACPI NVS)
BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
447MB LOWMEM available.
On node 0 totalpages: 114672
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 110576 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @ 0x000fa2e0
ACPI: RSDT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x1bff0000
ACPI: FADT (v002 AMIINT SiS740XX 0x00000011 MSFT 0x0100000b) @ 0x1bff0030
ACPI: DSDT (v001 SiS 740 0x00000100 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 1c000000 (gap: 1c000000:e3ee0000)
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=Linux ro root=301 splash=silent
apm=power-off nomce
bootsplash: silent mode.
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01403000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1593.363 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 448792k/458688k available (3064k kernel code, 9352k reserved,
1213k data, 216k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3189.34 BogoMIPS
(lpj=6378691)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 00000000
00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000020 00000000
00000000 00000000
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0c20)
CPU0: AMD Athlon(tm) XP 1900+ stepping 02
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
checking if image is initramfs...it isn't (no cpio magic); looks like an
initrd
Freeing initrd memory: 3k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=2
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
Uncovering SIS962 that hid as a SIS503 (compatible=0)
Enabling SiS 96x SMBus.
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 7 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: cfd00000-cfefffff
PREFETCH window: b7a00000-c7bfffff
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFS: nTxBlock = 3507, nTxLock = 28059
SGI XFS with ACLs, security attributes, realtime, large block numbers,
no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP030b:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: ST3250823A, ATA DISK drive
hdb: HL-DT-ST CD-ROM GCR-8520B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 1024KiB
hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63,
UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdb: ATAPI 52X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
libata version 1.12 loaded.
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid10 personality registered as nr 9
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 1964.000 MB/sec
raid5: using function: pIII_sse (1964.000 MB/sec)
raid6: int32x1 607 MB/s
raid6: int32x2 767 MB/s
raid6: int32x4 450 MB/s
raid6: int32x8 457 MB/s
raid6: mmxx1 1346 MB/s
raid6: mmxx2 2301 MB/s
raid6: sse1x1 1267 MB/s
raid6: sse1x2 2087 MB/s
raid6: using algorithm sse1x2 (2087 MB/s)
md: raid6 personality registered as nr 8
md: multipath personality registered as nr 7
md: faulty personality registered as nr 10
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@xxxxxxxxxx
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 15
Using IPI Shortcut mode
Suspend2 Core.
Suspend2 Compression Driver loading.
Suspend2 Encryption Driver loading.
Suspend2 Swap Writer loading.
Suspend2 FileWriter loading.
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Suspend2: Initrd lacks echo > /proc/software_suspend/do_resume.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... <6>kjournald starting. Commit
interval 5 seconds
okay
Freeing unused kernel memory: 216k freed
logips2pp: Detected unknown logitech mouse model 62
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
ts: Compaq touchscreen protocol output
Suspend2 2.2-rc7: You need to use a resume2= command line parameter to
tell Suspend2 where to look for an image.
Suspend2 2.2-rc7: Resume2 parameter is empty. Suspending will be disabled.
Suspend2 2.2-rc7: Missing or invalid storage location (resume2=
parameter). Please correct and rerun lilo (or equivalent) before suspending.
Adding 1028152k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
Real Time Clock Driver v1.12
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: CPU0 (power states: C1[C1])
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
i2c-sis96x version 1.0.0
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
sis900.c: v1.08.08 Jan. 22 2005
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKD] -> GSI 11 (level,
low) -> IRQ 11
0000:00:04.0: VIA 6103 PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 11, 00:0a:e6:53:99:ab.
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKD] -> GSI 11 (level,
low) -> IRQ 11
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0d.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xd000. Vers LK1.1.19
Linux video capture interface: v1.00
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.0 (tagged release) loading
ivtv: Linux version: 2.6.13.2-chw-3 SMP preempt 586 gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv0: Autodetected WinTV PVR 350 card (iTVC15 based)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 5 (level, low)
-> IRQ 5
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
msp34xx: ivtv version
msp34xx: init: chip=MSP3418W-B3, has NICAM support, simple (D) mode,
simpler (G) no-thread mode
msp34xx: $Id$ compiled on: Oct 9 2005 22:52:16
ivtv0: i2c attach to card #0 ok [client=MSP3418W-B3, addr=40]
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
tveeprom: ivtv version
tveeprom: Hauppauge: model = 48139, rev = K157, serial# = 7612060
tveeprom: tuner = Philips FM1216 ME MK3 (idx = 57, type = 38)
tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom =
0x74, v4l2 = 0x00400e17)
tveeprom: audio processor = MSP4418 (type = 19)
tveeprom: decoder processor = SAA7115 (type = 13)
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
saa7127 1-0044: saa7127 found @ 0x88 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44]
tda9885/6/7: (ivtv) chip found @ 0x86
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: loading /lib/modules/ivtv-fw-enc.bin
ivtv0: loading /lib/modules/ivtv-fw-dec.bin
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total)
ivtv0: loading /lib/modules/ivtv_init_mpeg.bin
tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv
i2c driver #0
spurious 8259A interrupt: IRQ7.
ivtv0: Initialized WinTV PVR 350, card #0
ivtv: ==================== END INIT IVTV ====================
Linux agpgart interface v0.101 (c) Dave Jones
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:02.7[C] -> Link [LNKC] -> GSI 10 (level,
low) -> IRQ 10
intel8x0_measure_ac97_clock: measured 55971 usecs
intel8x0: clocking to 48000
NET: Registered protocol family 17
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bt878: AUDIO driver version 0.0.0 loaded
saa7146: register extension 'dvb'.
saa7146: register extension 'budget dvb'.
saa7146: register extension 'budget_ci dvb'.
saa7146: register extension 'budget_av'.
usbcore: registered new driver ttusb
usbcore: registered new driver ttusb-dec
NET: Registered protocol family 10
Disabled Privacy Extensions on device c04d8ba0(lo)
IPv6 over IPv4 tunneling driver
ttyS0: LSR safety check engaged!
ttyS0: LSR safety check engaged!
ttyS1: LSR safety check engaged!
ttyS1: LSR safety check engaged!
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: Media Link Off
eth0: no IPv6 routers present
eth0: Media Link On 100mbps full-duplex
Warning: /proc/ide/hd?/settings interface is obsolete, and will be
removed soon!
eth0: Media Link On 100mbps full-duplex
lirc_dev: IR Remote Control driver registered, at major 61
cx2388x v4l2 driver version 0.0.5 loaded
lirc_i2c: chip found @ 0x18 (Hauppauge IR)
ivtv0: i2c attach to card #0 ok [client=Hauppauge IR, addr=18]
lirc_dev: lirc_register_plugin: sample_rate: 10
input: PC Speaker
eth0: no IPv6 routers present
agpgart: Detected SiS 740 chipset
agpgart: AGP aperture is 32M @ 0xd0000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
---------------
Glæder mig til at høre fra jer.
Hilsen Niels Andersen.
Follow ups
