touch-packages team mailing list archive

Thread
Date
[Bug 1475921] [NEW] Hp printer recognized, connected, and set at lpt0 on a parallel port just can not print

To: touch-packages@xxxxxxxxxxxxxxxxxxx
From: Robert Henley <1475921@xxxxxxxxxxxxxxxxxx>
Date: Sat, 18 Jul 2015 21:24:02 -0000
Reply-to: Bug 1475921 <1475921@xxxxxxxxxxxxxxxxxx>
Sender: bounces@xxxxxxxxxxxxx
Public bug reported:

Cmd line output from Term

robert@spareparts ~ $ lsmod | grep lp
usblp                  18277  0 
lp                     13299  0 
parport                40836  3 lp,ppdev,parport_pc
drm_kms_helper         48868  1 nouveau
drm                   244037  5 ttm,drm_kms_helper,nouveau
robert@spareparts ~ $ lsmod | grep ppdev
ppdev                  17391  0 
parport                40836  3 lp,ppdev,parport_pc
robert@spareparts ~ $ lsmod | grep parport_pc
parport_pc             31981  2 
parport                40836  3 lp,ppdev,parport_pc
robert@spareparts ~ $ dmesg | grep par
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.080220] regulator-dummy: no parameters
[    0.099368] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-1f] only partially covers this bridge
[    0.116867] hpet0: 4 comparators, 64-bit 25.000000 MHz counter
[    0.764148] Asymmetric key parser 'x509' registered
[    1.304060] ahci 0000:06:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
[    1.760491]  sdb: unknown partition table
[    1.762354]  sde: unknown partition table
[    1.765859]  sdd: unknown partition table
[    1.766673]  sdc: unknown partition table
[    3.095589] ppdev: user-space parallel port driver
[    3.105129] PCI parallel port detected: 1415:c11c, I/O at 0xee00(0xed00), IRQ 18
[    3.105164] parport0: PC-style at 0xee00 (0xed00), irq 18, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[    3.200344] lp0: using parport0 (interrupt-driven).
[    3.200348] PCI parallel port detected: 1415:c11c, I/O at 0xec00(0xeb00), IRQ 18
[    3.200387] parport1: PC-style at 0xec00 (0xeb00), irq 18, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[    3.296140] lp1: using parport1 (interrupt-driven).
[12183.100015] parport0: BUSY timeout (1) in compat_write_block_pio
[12354.820018] parport0: BUSY timeout (1) in compat_write_block_pio
[12384.892008] parport0: BUSY timeout (1) in compat_write_block_pio
[12389.818249] parport0: BUSY timeout (-4) in compat_write_block_pio
[12479.404429] parport1: lp tried to release parport when not owner
[12479.404434] parport1: ppdev1 forgot to release port
robert@spareparts ~ $ ls -l /dev/lp* /dev/parport*
crw-rw---- 1 root lp  6, 0 Jul 18 11:06 /dev/lp0
crw-rw---- 1 root lp  6, 1 Jul 18 11:06 /dev/lp1
crw-rw-rw- 1 lp   lp 99, 0 Jul 18 11:06 /dev/parport0
crw-rw-rw- 1 lp   lp 99, 1 Jul 18 11:06 /dev/parport1
robert@spareparts ~ $ ls -l /proc/sys/dev/parport/parport*/autoprobe
-r--r--r-- 1 root root 0 Jul 18 15:30 /proc/sys/dev/parport/parport0/autoprobe
-r--r--r-- 1 root root 0 Jul 18 15:30 /proc/sys/dev/parport/parport1/autoprobe
robert@spareparts ~ $ sudo cat /proc/sys/dev/parport/parport*/autoprobe*
[sudo] password for robert: 
robert@spareparts ~ $ sudo cat /proc/sys/dev/parport/parport*/autoprobe*
robert@spareparts ~ $ lpinfo -v
network socket
network https
network ipp14
network ipp
network ipps
network http
serial serial:/dev/ttyS0?baud=115200
network smb
network lpd
robert@spareparts ~ $ /usr/lib/cups/backend/parallel
direct parallel:/dev/lp0 "HP OfficeJet T Series" "HP OfficeJet T Series LPT #1" "MFG:Hewlett-Packard;MDL:OfficeJet T Series;CMD:MLC,PCL,PML;CLASS:PRINTER;DESCRIPTION:Hewlett-Packard OfficeJet T Series;VSTATUS:$HB0$FC0,FF,DN,IDLE,CUT;" ""
direct parallel:/dev/lp1 "unknown" "LPT #2" "" ""
robert@spareparts ~ $ sudo /usr/lib/cups/backend/parallel
direct parallel:/dev/lp0 "HP OfficeJet T Series" "HP OfficeJet T Series LPT #1" "MFG:Hewlett-Packard;MDL:OfficeJet T Series;CMD:MLC,PCL,PML;CLASS:PRINTER;DESCRIPTION:Hewlett-Packard OfficeJet T Series;VSTATUS:$HB0$FC0,FF,DN,IDLE,CUT;" ""
direct parallel:/dev/lp1 "unknown" "LPT #2" "" ""
robert@spareparts ~ $ 


Hplip has been manually installed with ppbuild, and CUPS has been updated

ProblemType: Bug
DistroRelease: Ubuntu 14.04
Package: cups 1.7.2-0ubuntu1.6
ProcVersionSignature: Ubuntu 3.13.0-37.64-generic 3.13.11.7
Uname: Linux 3.13.0-37-generic i686
ApportVersion: 2.14.1-0ubuntu3.11
Architecture: i386
Date: Sat Jul 18 16:02:06 2015
InstallationDate: Installed on 2015-07-17 (1 days ago)
InstallationMedia: Linux Mint 17.1 "Rebecca" - Release i386 20150108
Lpstat:
 device for Hewlett-Packard-OfficeJet-T-Series: parallel:/dev/lp0
 device for PSC-900-Series: usb://HP/PSC%20900%20Series?serial=MY19DB206ZWP
 device for PSC_950xi: hp:/usb/PSC_950xi?serial=MY19DB206ZWP
Lsusb:
 Bus 002 Device 002: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader)
 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
 Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
 Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
MachineType: EVGA GeForce 9300 Series
Papersize: letter
PpdFiles:
 PSC_950xi: HP PSC 950xi, hpcups 3.15.6
 PSC-900-Series: HP PSC 900 Series, hpcups 3.14.3
 Hewlett-Packard-OfficeJet-T-Series: HP Officejet T Series, hpcups 3.15.6
ProcEnviron:
 TERM=xterm
 PATH=(custom, no user)
 XDG_RUNTIME_DIR=<set>
 LANG=en_US.UTF-8
 SHELL=/bin/bash
ProcKernelCmdLine: BOOT_IMAGE=/vmlinuz-3.13.0-37-generic root=UUID=fe034ccc-f1e7-44e0-951e-39acab43e203 ro quiet splash vt.handoff=7
SourcePackage: cups
UpgradeStatus: No upgrade log present (probably fresh install)
dmi.bios.date: 03/02/2009
dmi.bios.vendor: Phoenix Technologies, LTD
dmi.bios.version: 6.00 PG
dmi.board.name: GeForce 9300 Series
dmi.board.vendor: EVGA
dmi.board.version: 1
dmi.chassis.asset.tag: Unknow
dmi.chassis.type: 3
dmi.chassis.vendor: EVGA
dmi.chassis.version: GeForce 9300 Series
dmi.modalias: dmi:bvnPhoenixTechnologies,LTD:bvr6.00PG:bd03/02/2009:svnEVGA:pnGeForce9300Series:pvr1:rvnEVGA:rnGeForce9300Series:rvr1:cvnEVGA:ct3:cvrGeForce9300Series:
dmi.product.name: GeForce 9300 Series
dmi.product.version: 1
dmi.sys.vendor: EVGA

** Affects: cups (Ubuntu)
     Importance: Undecided
         Status: New


** Tags: apport-bug i386 rebecca third-party-packages

-- 
You received this bug notification because you are a member of Ubuntu
Touch seeded packages, which is subscribed to cups in Ubuntu.
https://bugs.launchpad.net/bugs/1475921

Title:
  Hp printer recognized,connected,and set at lpt0 on a parallel port
  just can not print

Status in cups package in Ubuntu:
  New

Bug description:
  Cmd line output from Term

  robert@spareparts ~ $ lsmod | grep lp
  usblp                  18277  0 
  lp                     13299  0 
  parport                40836  3 lp,ppdev,parport_pc
  drm_kms_helper         48868  1 nouveau
  drm                   244037  5 ttm,drm_kms_helper,nouveau
  robert@spareparts ~ $ lsmod | grep ppdev
  ppdev                  17391  0 
  parport                40836  3 lp,ppdev,parport_pc
  robert@spareparts ~ $ lsmod | grep parport_pc
  parport_pc             31981  2 
  parport                40836  3 lp,ppdev,parport_pc
  robert@spareparts ~ $ dmesg | grep par
  [    0.000000] Booting paravirtualized kernel on bare hardware
  [    0.080220] regulator-dummy: no parameters
  [    0.099368] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-1f] only partially covers this bridge
  [    0.116867] hpet0: 4 comparators, 64-bit 25.000000 MHz counter
  [    0.764148] Asymmetric key parser 'x509' registered
  [    1.304060] ahci 0000:06:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
  [    1.760491]  sdb: unknown partition table
  [    1.762354]  sde: unknown partition table
  [    1.765859]  sdd: unknown partition table
  [    1.766673]  sdc: unknown partition table
  [    3.095589] ppdev: user-space parallel port driver
  [    3.105129] PCI parallel port detected: 1415:c11c, I/O at 0xee00(0xed00), IRQ 18
  [    3.105164] parport0: PC-style at 0xee00 (0xed00), irq 18, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
  [    3.200344] lp0: using parport0 (interrupt-driven).
  [    3.200348] PCI parallel port detected: 1415:c11c, I/O at 0xec00(0xeb00), IRQ 18
  [    3.200387] parport1: PC-style at 0xec00 (0xeb00), irq 18, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
  [    3.296140] lp1: using parport1 (interrupt-driven).
  [12183.100015] parport0: BUSY timeout (1) in compat_write_block_pio
  [12354.820018] parport0: BUSY timeout (1) in compat_write_block_pio
  [12384.892008] parport0: BUSY timeout (1) in compat_write_block_pio
  [12389.818249] parport0: BUSY timeout (-4) in compat_write_block_pio
  [12479.404429] parport1: lp tried to release parport when not owner
  [12479.404434] parport1: ppdev1 forgot to release port
  robert@spareparts ~ $ ls -l /dev/lp* /dev/parport*
  crw-rw---- 1 root lp  6, 0 Jul 18 11:06 /dev/lp0
  crw-rw---- 1 root lp  6, 1 Jul 18 11:06 /dev/lp1
  crw-rw-rw- 1 lp   lp 99, 0 Jul 18 11:06 /dev/parport0
  crw-rw-rw- 1 lp   lp 99, 1 Jul 18 11:06 /dev/parport1
  robert@spareparts ~ $ ls -l /proc/sys/dev/parport/parport*/autoprobe
  -r--r--r-- 1 root root 0 Jul 18 15:30 /proc/sys/dev/parport/parport0/autoprobe
  -r--r--r-- 1 root root 0 Jul 18 15:30 /proc/sys/dev/parport/parport1/autoprobe
  robert@spareparts ~ $ sudo cat /proc/sys/dev/parport/parport*/autoprobe*
  [sudo] password for robert: 
  robert@spareparts ~ $ sudo cat /proc/sys/dev/parport/parport*/autoprobe*
  robert@spareparts ~ $ lpinfo -v
  network socket
  network https
  network ipp14
  network ipp
  network ipps
  network http
  serial serial:/dev/ttyS0?baud=115200
  network smb
  network lpd
  robert@spareparts ~ $ /usr/lib/cups/backend/parallel
  direct parallel:/dev/lp0 "HP OfficeJet T Series" "HP OfficeJet T Series LPT #1" "MFG:Hewlett-Packard;MDL:OfficeJet T Series;CMD:MLC,PCL,PML;CLASS:PRINTER;DESCRIPTION:Hewlett-Packard OfficeJet T Series;VSTATUS:$HB0$FC0,FF,DN,IDLE,CUT;" ""
  direct parallel:/dev/lp1 "unknown" "LPT #2" "" ""
  robert@spareparts ~ $ sudo /usr/lib/cups/backend/parallel
  direct parallel:/dev/lp0 "HP OfficeJet T Series" "HP OfficeJet T Series LPT #1" "MFG:Hewlett-Packard;MDL:OfficeJet T Series;CMD:MLC,PCL,PML;CLASS:PRINTER;DESCRIPTION:Hewlett-Packard OfficeJet T Series;VSTATUS:$HB0$FC0,FF,DN,IDLE,CUT;" ""
  direct parallel:/dev/lp1 "unknown" "LPT #2" "" ""
  robert@spareparts ~ $ 

  
  Hplip has been manually installed with ppbuild, and CUPS has been updated

  ProblemType: Bug
  DistroRelease: Ubuntu 14.04
  Package: cups 1.7.2-0ubuntu1.6
  ProcVersionSignature: Ubuntu 3.13.0-37.64-generic 3.13.11.7
  Uname: Linux 3.13.0-37-generic i686
  ApportVersion: 2.14.1-0ubuntu3.11
  Architecture: i386
  Date: Sat Jul 18 16:02:06 2015
  InstallationDate: Installed on 2015-07-17 (1 days ago)
  InstallationMedia: Linux Mint 17.1 "Rebecca" - Release i386 20150108
  Lpstat:
   device for Hewlett-Packard-OfficeJet-T-Series: parallel:/dev/lp0
   device for PSC-900-Series: usb://HP/PSC%20900%20Series?serial=MY19DB206ZWP
   device for PSC_950xi: hp:/usb/PSC_950xi?serial=MY19DB206ZWP
  Lsusb:
   Bus 002 Device 002: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader)
   Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
   Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
   Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
   Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
  MachineType: EVGA GeForce 9300 Series
  Papersize: letter
  PpdFiles:
   PSC_950xi: HP PSC 950xi, hpcups 3.15.6
   PSC-900-Series: HP PSC 900 Series, hpcups 3.14.3
   Hewlett-Packard-OfficeJet-T-Series: HP Officejet T Series, hpcups 3.15.6
  ProcEnviron:
   TERM=xterm
   PATH=(custom, no user)
   XDG_RUNTIME_DIR=<set>
   LANG=en_US.UTF-8
   SHELL=/bin/bash
  ProcKernelCmdLine: BOOT_IMAGE=/vmlinuz-3.13.0-37-generic root=UUID=fe034ccc-f1e7-44e0-951e-39acab43e203 ro quiet splash vt.handoff=7
  SourcePackage: cups
  UpgradeStatus: No upgrade log present (probably fresh install)
  dmi.bios.date: 03/02/2009
  dmi.bios.vendor: Phoenix Technologies, LTD
  dmi.bios.version: 6.00 PG
  dmi.board.name: GeForce 9300 Series
  dmi.board.vendor: EVGA
  dmi.board.version: 1
  dmi.chassis.asset.tag: Unknow
  dmi.chassis.type: 3
  dmi.chassis.vendor: EVGA
  dmi.chassis.version: GeForce 9300 Series
  dmi.modalias: dmi:bvnPhoenixTechnologies,LTD:bvr6.00PG:bd03/02/2009:svnEVGA:pnGeForce9300Series:pvr1:rvnEVGA:rnGeForce9300Series:rvr1:cvnEVGA:ct3:cvrGeForce9300Series:
  dmi.product.name: GeForce 9300 Series
  dmi.product.version: 1
  dmi.sys.vendor: EVGA

To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/cups/+bug/1475921/+subscriptions
Follow ups

[Bug 1475921] Re: Hp printer recognized, connected, and set at lpt0 on a parallel port just can not print
From: Launchpad Bug Tracker, 2015-09-21
[Bug 1475921] terminal output
From: Robert Henley, 2015-07-23
[Bug 1475921] Re: Hp printer recognized, connected, and set at lpt0 on a parallel port just can not print
From: Till Kamppeter, 2015-07-22
[Bug 1475921] output from terminal
From: Robert Henley, 2015-07-22
[Bug 1475921] Re: Hp printer recognized, connected, and set at lpt0 on a parallel port just can not print
From: Robert Henley, 2015-07-20
[Bug 1475921] Re: Hp printer recognized, connected, and set at lpt0 on a parallel port just can not print
From: Till Kamppeter, 2015-07-20
[Bug 1475921] Re: Hp printer recognized, connected, and set at lpt0 on a parallel port just can not print
From: Till Kamppeter, 2015-07-19