ubuntu-x-swat team mailing list archive

Thread
Date
[Bug 189694] Re: [i855GME] maximum resolution limited to 1024x768

To: ubuntu-x-swat@xxxxxxxxxxxxxxxxxxx
From: RgnKjnVA <RgnKjnVA@xxxxxxx>
Date: Fri, 08 May 2009 04:56:07 -0000
Reply-to: Bug 189694 <189694@xxxxxxxxxxxxxxxxxx>
Sender: bounces@xxxxxxxxxxxxx
I'm experiencing this on a Dell Latitude D610 running Intrepid. A co-
worker with the same laptop has this issue running Jaunty. I'm willing
to assist in debug because I would much prefer 1280x1024 but only get
1024x768 regardless of config.

~$ sudo ddcprobe
vbe: VESA 3.0 detected.
oem: Intel(r)915GM/910ML/915MS Graphics Chip Accelerated VGA BIOS
vendor: Intel Corporation
product: Intel(r)915GM/910ML/915MS Graphics Controller Hardware Version 0.0
memory: 7872kb
mode: 1280x1024x256
mode: 1280x1024x64k
mode: 1280x1024x16m
mode: 1024x768x256
mode: 1024x768x64k
mode: 1024x768x16m
mode: 640x480x16m
mode: 800x600x64k
mode: 800x600x16m
mode: 640x480x256
mode: 800x600x256
mode: 640x480x64k
edid: 
edid: 1 3
id: 4258
eisa: SEC4258
serial: 00000000
manufacture: 0 2004
input: analog signal.
screensize: 29 21
gamma: 2.200000
dpms: RGB, no active off, no suspend, no standby
dtiming: 1024x768@74
dtiming: 1024x768@61
monitorid: H4400141XB
monitorid: �����`0


~$ more /etc/X11/xorg.conf
# xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
#   sudo dpkg-reconfigure -phigh xserver-xorg

Section "Files"
EndSection

# commented out by update-manager, HAL is now used
#Section "InputDevice"
#	Identifier	"Generic Keyboard"
#	Driver		"kbd"
#	Option		"CoreKeyboard"
#	Option		"XkbRules"	"xorg"
#	Option		"XkbModel"	"pc105"
#	Option		"XkbLayout"	"us"
#EndSection

# commented out by update-manager, HAL is now used
#Section "InputDevice"
#	Identifier	"Configured Mouse"
#	Driver		"mouse"
#	Option		"CorePointer"
#	Option		"Device"		"/dev/input/mice"
#	Option		"Protocol"		"ImPS/2"
#	Option		"ZAxisMapping"		"4 5"
#	Option		"Emulate3Buttons"	"true"
#EndSection

# commented out by update-manager, HAL is now used
#Section "InputDevice"
#	Identifier	"Synaptics Touchpad"
#	Driver		"synaptics"
#	Option		"SendCoreEvents"	"true"
#	Option		"Device"		"/dev/psaux"
#	Option		"Protocol"		"auto-dev"
#	Option		"HorizEdgeScroll"	"0"
#EndSection

# commented out by update-manager, HAL is now used
#Section "InputDevice"
#	Driver		"wacom"
#	Identifier	"stylus"
#	Option		"Device"	"/dev/input/wacom"
#	Option		"Type"		"stylus"
#	Option		"ForceDevice"	"ISDV4"		# Tablet PC ONLY
#EndSection

# commented out by update-manager, HAL is now used
#Section "InputDevice"
#	Driver		"wacom"
#	Identifier	"eraser"
#	Option		"Device"	"/dev/input/wacom"
#	Option		"Type"		"eraser"
#	Option		"ForceDevice"	"ISDV4"		# Tablet PC ONLY
#EndSection

# commented out by update-manager, HAL is now used
#Section "InputDevice"
#	Driver		"wacom"
#	Identifier	"cursor"
#	Option		"Device"	"/dev/input/wacom"
#	Option		"Type"		"cursor"
#	Option		"ForceDevice"	"ISDV4"		# Tablet PC ONLY
#EndSection

Section "Device"
	Identifier	"Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller"
	Driver		"intel"
	BusID		"PCI:0:2:0"
EndSection

Section "Monitor"
	Identifier	"Generic Monitor"
	Option		"DPMS"
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Device		"Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller"
	Monitor		"Generic Monitor"
	DefaultDepth	24
	SubSection "Display"
		Modes "1280x1024" "1024x768"
	EndSubSection
EndSection

Section "ServerLayout"
	Identifier	"Default Layout"
	Screen		"Default Screen"
# commented out by update-manager, HAL is now used
#	InputDevice	"Generic Keyboard"
# commented out by update-manager, HAL is now used
#	InputDevice	"Configured Mouse"

# Uncomment if you have a wacom tablet
#	InputDevice     "stylus"	"SendCoreEvents"
#	InputDevice     "cursor"	"SendCoreEvents"
#	InputDevice     "eraser"	"SendCoreEvents"
# commented out by update-manager, HAL is now used
#	InputDevice	"Synaptics Touchpad"
EndSection

~$ lspci -vvnn
00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller [8086:2590] (rev 03)
	Subsystem: Dell Device [1028:0182]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: agpgart-intel
	Kernel modules: intel-agp

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 03)
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K]
	Region 1: I/O ports at ec38 [size=8]
	Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
	Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K]
	Capabilities: <access denied>
	Kernel modules: intelfb

00:02.1 Display controller [0380]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2792] (rev 03)
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K]
	Capabilities: <access denied>

00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Memory behind bridge: dfd00000-dfdfffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport-driver
	Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 [8086:2658] (rev 03)
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 4: I/O ports at bf80 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 [8086:2659] (rev 03)
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 4: I/O ports at bf60 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 [8086:265a] (rev 03)
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 18
	Region 4: I/O ports at bf40 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.3 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 [8086:265b] (rev 03)
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 19
	Region 4: I/O ports at bf20 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 03) (prog-if 20)
	Subsystem: Dell Device [1028:0182]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at ffa80800 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev d3) (prog-if 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=03, subordinate=07, sec-latency=32
	Memory behind bridge: dfc00000-dfcfffff
	Prefetchable memory behind bridge: 0000000088000000-000000008bffffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller [8086:266e] (rev 03)
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: I/O ports at ed00 [size=256]
	Region 1: I/O ports at ec40 [size=64]
	Region 2: Memory at dfebfe00 (32-bit, non-prefetchable) [size=512]
	Region 3: Memory at dfebfd00 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: Intel ICH
	Kernel modules: snd-intel8x0

00:1e.3 Modem [0703]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller [8086:266d] (rev 03)
	Subsystem: Conexant Systems, Inc. Device [14f1:5423]
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin B routed to IRQ 17
	Region 0: I/O ports at ee00 [size=256]
	Region 1: I/O ports at ec80 [size=128]
	Capabilities: <access denied>
	Kernel modules: snd-intel8x0m

00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge [8086:2641] (rev 03)
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Kernel modules: iTCO_wdt, intel-rng

00:1f.2 IDE interface [0101]: Intel Corporation 82801FBM (ICH6M) SATA Controller [8086:2653] (rev 03) (prog-if 80 [Master])
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at bfa0 [size=16]
	Capabilities: <access denied>
	Kernel driver in use: ata_piix
	Kernel modules: ata_piix, ahci

00:1f.3 SMBus [0c05]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller [8086:266a] (rev 03)
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin B routed to IRQ 10
	Region 4: I/O ports at 10c0 [size=32]
	Kernel modules: i2c-i801

02:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express [14e4:1677] (rev 01)
	Subsystem: Dell Device [1028:0182]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at dfdf0000 (64-bit, non-prefetchable) [size=64K]
	Expansion ROM at <ignored> [disabled]
	Capabilities: <access denied>
	Kernel driver in use: tg3
	Kernel modules: tg3

03:01.0 CardBus bridge [0607]: Texas Instruments PCI6515 Cardbus Controller [104c:8036]
	Subsystem: Dell Device [1028:0182]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168, Cache Line Size: 128 bytes
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at dfc00000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=03, secondary=04, subordinate=07, sec-latency=176
	Memory window 0: 88000000-8bfff000 (prefetchable)
	Memory window 1: 8c000000-8ffff000
	I/O window 0: 00001400-000014ff
	I/O window 1: 00001800-000018ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001
	Kernel driver in use: yenta_cardbus
	Kernel modules: yenta_socket

03:01.5 Communication controller [0780]: Texas Instruments PCI6515 SmartCard Controller [104c:8038]
	Subsystem: Dell Device [1028:0182]
	Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at dfcfd000 (32-bit, non-prefetchable) [size=4K]
	Region 1: Memory at dfcfe000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>

03:03.0 Network controller [0280]: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection [8086:4220] (rev 05)
	Subsystem: Intel Corporation Device [8086:2721]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (750ns min, 6000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at dfcff000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: ipw2200
	Kernel modules: ipw2200

-- 
[i855GME] maximum resolution limited to 1024x768 
https://bugs.launchpad.net/bugs/189694
You received this bug notification because you are a member of Ubuntu-X,
which is subscribed to xserver-xorg-video-intel in ubuntu.