← Back to team overview

sslug-teknik team mailing list archive

  1. sslug-teknik team
  2. Mailing list archive
  3. Message #97504

Re: klikkende harddisk

  Thread Previous • Date Previous • • Thread Next 
Frank Damgaard wrote:

Lars Madsen skrev:
 .....

ngoen der ved hvad dette betyder fra bios (Vedr. denne harddisk)

Ultra DMA Mode-5 S.M.A.R.T Capable and Status BAD

man bliver saa givet muligheden for at fortsaette med F1 og det virker
fint.

Nu er jeg bootet over paa en gammel disk i stedet.



du kan jo prøve "smartctl -a /dev/sdx" på drevet
hvis det er enablet, ellers først: "smartctl -s on /dev/sdx"
men se manual side for detaljer.

Du har checket at det ikke er nogle kabler/stik der måske ikke
har helt god forbindelse?





laver lige tekst spam:
Her var resultatet. Jeg har smidt det meste af min data over paa mit raid, og gaar i gang med at installere paa en anden disk 

smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.10 family
Device Model:     ST3500630A
Serial Number:    9QG9QLME
Firmware Version: 3.AAF
User Capacity:    500.107.862.016 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Sat Feb  7 16:56:46 2009 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed 
					without error or no self-test has ever
					been run.
Total time to complete Offline
data collection: 		 ( 430) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 163) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 119 097 006 Pre-fail Always - 210637582 3 Spin_Up_Time 0x0003 095 092 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 256 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 044 039 030 Pre-fail Always - 7327257260380 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 832 10 Spin_Retry_Count 0x0013 080 080 097 Pre-fail Always FAILING_NOW 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 283 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 066 053 045 Old_age Always - 34 (Lifetime Min/Max 18/34) 194 Temperature_Celsius 0x0022 034 047 000 Old_age Always - 34 (0 14 0 0) 195 Hardware_ECC_Recovered 0x001a 078 060 000 Old_age Always - 181354618 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 

SMART Error Log Version: 1
ATA Error Count: 3
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 3 occurred at disk power-on lifetime: 303 hours (12 days + 15 hours)
When the command that caused the error occurred, the device was active or idle. 

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 01 00 00 a0  Error: ICRC, ABRT 1 sectors at LBA = 0x00000001 = 1

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 01 01 00 00 a0 00      00:00:12.271  READ DMA
ef 03 45 01 10 00 a0 00 00:00:12.270 SET FEATURES [Set transfer mode] ef 03 0c 01 10 00 a0 00 00:00:12.236 SET FEATURES [Set transfer mode] 
  c6 da 10 01 4f c2 a0 00      00:00:05.023  SET MULTIPLE MODE
  b0 da 00 01 4f c2 a0 00      09:10:38.209  SMART RETURN STATUS

Error 2 occurred at disk power-on lifetime: 303 hours (12 days + 15 hours)
When the command that caused the error occurred, the device was active or idle. 

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 01 00 00 a0  Error: ICRC, ABRT 1 sectors at LBA = 0x00000001 = 1

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 01 01 00 00 a0 00      00:00:12.286  READ DMA
ef 03 45 01 10 00 a0 00 00:00:12.286 SET FEATURES [Set transfer mode] ef 03 0c 01 10 00 a0 00 00:00:12.251 SET FEATURES [Set transfer mode] 
  c6 da 10 01 4f c2 a0 00      00:00:10.294  SET MULTIPLE MODE
  b0 da 00 01 4f c2 a0 00      09:10:38.209  SMART RETURN STATUS

Error 1 occurred at disk power-on lifetime: 303 hours (12 days + 15 hours)
When the command that caused the error occurred, the device was active or idle. 

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 01 00 00 a0  Error: ICRC, ABRT 1 sectors at LBA = 0x00000001 = 1

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 01 01 00 00 a0 00      00:00:12.271  READ DMA
ef 03 45 01 10 00 a0 00 00:00:12.271 SET FEATURES [Set transfer mode] ef 03 0c 01 10 00 a0 00 00:00:12.236 SET FEATURES [Set transfer mode] 
  c6 da 10 01 4f c2 a0 00      00:00:10.399  SET MULTIPLE MODE
  b0 da 00 01 4f c2 a0 00      09:10:38.209  SMART RETURN STATUS

SMART Self-test log structure revision number 1

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Follow ups

References

  Thread Previous • Date Previous • • Thread Next