kicad-developers team mailing list archive

[Bob Gustafson <bobgus@xxxxxxx>]

Whoops - comments on my previous message only apply to eeschema view.

The pcbnew view (openGL) will scroll so picture is 1/10 the area of the
window, rather than stopping when whole paper is visible in the window.

Scrolling and Zooming is jumpy and slow.

Scrolling requires two finger + shift to go up and down. two finger +
command to go left right (and picture motion is opposite to finger motion)

Scrolling should be the same as eechema - two finger + shift gives two
dimensional scroll - very intuitive.

Still needs some work.

Bob G

On 11/13/2015 11:03 AM, Bob Gustafson wrote:
> Wow - lots of reasonable changes to the OSX version:
>
>   Two finger + Shift - trackpad works intuitively like it should (at
> least for me) - move fingers left, picture moves left, move fingers
> up, picture moves up, and scroll stops when edge of paper is reached.
>
>   Two finger - trackpad zoom works more slowly and smoothly.
>
> I haven't tested beyond the trackpad motions for now (as these were
> blockers for me).
>
> Thanks much to the whole team - including the OSXers.
>
> Bob G
>
> On 11/13/2015 10:01 AM, Adam Wolf wrote:
> > Both should work.  It was me tweaking things that shouldn't impact
> > the build, things like Jenkins retries and timeouts and stuff like that.
> >
> > On Fri, Nov 13, 2015 at 9:51 AM, Johannes Maibaum
> > <jmaibaum@xxxxxxxxx> wrote:
> >
> >     Hi Adam,
> >
> >     > Am 13.11.2015 um 15:32 schrieb Adam Wolf
> >     <adamwolf@xxxxxxxxxxxxxxxxxxxx>:
> >     >
> >     > Hi folks,
> >     >
> >     > I uploaded test packages of kicad and kicad-extras from the RC2
> >     branch to the regular nightlies area.  If someone else could
> >     download them and make sure they seem OK before publicizing this,
> >     that would be appreciated.
> >     >
> >     > http://downloads.kicad-pcb.org/osx/
> >
> >     In that folder, there two packages each (2x kicad-4.0.0-rc2… and
> >     2x kicad-extras-4.0.0-rc2) that, from their names, look to be
> >     built from identical snapshots, but at different times.
> >
> >     Is their any reason I should check both builds? I’m currently
> >     only downloading the newer ones…
> >
> >
> >     Best,
> >
> >     Johannes
> >
> >     >
> >     > Thanks!
> >     >
> >     > Adam Wolf
> >     > Cofounder and Engineer
> >     > W&L
> >
> >     _______________________________________________
> >     Mailing list: https://launchpad.net/~kicad-developers
> >     <https://launchpad.net/%7Ekicad-developers>
> >     Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
> >     <mailto:kicad-developers@xxxxxxxxxxxxxxxxxxx>
> >     Unsubscribe : https://launchpad.net/~kicad-developers
> >     <https://launchpad.net/%7Ekicad-developers>
> >     More help   : https://help.launchpad.net/ListHelp
> >
> >
> >
> >
> > _______________________________________________
> > Mailing list:https://launchpad.net/~kicad-developers
> > Post to     :kicad-developers@xxxxxxxxxxxxxxxxxxx
> > Unsubscribe :https://launchpad.net/~kicad-developers
> > More help   :https://help.launchpad.net/ListHelp
>
>
>
> _______________________________________________
> Mailing list: https://launchpad.net/~kicad-developers
> Post to     : kicad-developers@xxxxxxxxxxxxxxxxxxx
> Unsubscribe : https://launchpad.net/~kicad-developers
> More help   : https://help.launchpad.net/ListHelp