Hi Bob!
There are no code changes in this RC2 package from the nightlies. I
made a new autobuilder for this build, and was looking for testers to
make sure the autobuilder seems ok.
It does.
Thanks!
Adam Wolf
Cofounder and Engineer
W&L
On Fri, Nov 13, 2015 at 11:49 AM, Bob Gustafson <bobgus@xxxxxxx
<mailto:bobgus@xxxxxxx>> wrote:
Whoops - comments on my previous message only apply to eeschema view.
The pcbnew view (openGL) will scroll so picture is 1/10 the area
of the window, rather than stopping when whole paper is visible in
the window.
Scrolling and Zooming is jumpy and slow.
Scrolling requires two finger + shift to go up and down. two
finger + command to go left right (and picture motion is opposite
to finger motion)
Scrolling should be the same as eechema - two finger + shift gives
two dimensional scroll - very intuitive.
Still needs some work.
Bob G
On 11/13/2015 11:03 AM, Bob Gustafson wrote:
Wow - lots of reasonable changes to the OSX version:
Two finger + Shift - trackpad works intuitively like it should
(at least for me) - move fingers left, picture moves left, move
fingers up, picture moves up, and scroll stops when edge of paper
is reached.
Two finger - trackpad zoom works more slowly and smoothly.
I haven't tested beyond the trackpad motions for now (as these
were blockers for me).
Thanks much to the whole team - including the OSXers.
Bob G
On 11/13/2015 10:01 AM, Adam Wolf wrote:
Both should work. It was me tweaking things that shouldn't
impact the build, things like Jenkins retries and timeouts and
stuff like that.
On Fri, Nov 13, 2015 at 9:51 AM, Johannes Maibaum
<jmaibaum@xxxxxxxxx <mailto:jmaibaum@xxxxxxxxx>> wrote:
Hi Adam,
> Am 13.11.2015 um 15:32 schrieb Adam Wolf
<adamwolf@xxxxxxxxxxxxxxxxxxxx
<mailto:adamwolf@xxxxxxxxxxxxxxxxxxxx>>:
>
> Hi folks,
>
> I uploaded test packages of kicad and kicad-extras from
the RC2 branch to the regular nightlies area. If someone
else could download them and make sure they seem OK before
publicizing this, that would be appreciated.
>
> http://downloads.kicad-pcb.org/osx/
In that folder, there two packages each (2x kicad-4.0.0-rc2…
and 2x kicad-extras-4.0.0-rc2) that, from their names, look
to be built from identical snapshots, but at different times.
Is their any reason I should check both builds? I’m
currently only downloading the newer ones…
Best,
Johannes
>
> Thanks!
>
> Adam Wolf
> Cofounder and Engineer
> W&L
_______________________________________________
Mailing list: https://launchpad.net/~kicad-developers
<https://launchpad.net/%7Ekicad-developers>
Post to : kicad-developers@xxxxxxxxxxxxxxxxxxx
<mailto:kicad-developers@xxxxxxxxxxxxxxxxxxx>
Unsubscribe : https://launchpad.net/~kicad-developers
<https://launchpad.net/%7Ekicad-developers>
More help : https://help.launchpad.net/ListHelp
_______________________________________________
Mailing list:https://launchpad.net/~kicad-developers
<https://launchpad.net/%7Ekicad-developers>
Post to :kicad-developers@xxxxxxxxxxxxxxxxxxx
<mailto:kicad-developers@xxxxxxxxxxxxxxxxxxx>
Unsubscribe :https://launchpad.net/~kicad-developers
<https://launchpad.net/%7Ekicad-developers>
More help :https://help.launchpad.net/ListHelp
_______________________________________________
Mailing list:https://launchpad.net/~kicad-developers
<https://launchpad.net/%7Ekicad-developers>
Post to :kicad-developers@xxxxxxxxxxxxxxxxxxx
<mailto:kicad-developers@xxxxxxxxxxxxxxxxxxx>
Unsubscribe :https://launchpad.net/~kicad-developers
<https://launchpad.net/%7Ekicad-developers>
More help :https://help.launchpad.net/ListHelp
_______________________________________________
Mailing list: https://launchpad.net/~kicad-developers
<https://launchpad.net/%7Ekicad-developers>
Post to : kicad-developers@xxxxxxxxxxxxxxxxxxx
<mailto:kicad-developers@xxxxxxxxxxxxxxxxxxx>
Unsubscribe : https://launchpad.net/~kicad-developers
<https://launchpad.net/%7Ekicad-developers>
More help : https://help.launchpad.net/ListHelp
