sslug-teknik team mailing list archive

[Frank Damgaard <frank_sslug@xxxxxxxxxxxxxx>]

Lars Madsen skrev:
 .....
>> hopla, doed RAM klods. De to sidste klarede fint memtest. Vil bestille
>> en ny, Gad vide om de stadigvak er daekket af garentien?
>>

> Jeg lavede lige en smartctl -t long paa den klikkende harddisk, her er
> resultatet af -a, hvis der var nogen som var interesseret

jeg antager den stadig "klikker", men ummidelbart siger smart ikke så
meget. Er -a efter ca. 3 timer som er den tid selv-test tager
da det ikke ser ud som om der er fundet nogen fejl.

Men da du har flere af den samme model, og hvis de andre ikke har
samme klik-lyde, så må der jo være noget anderledes.
Du kan evt. sammenligne smartctl mellem diskene og se om der
er noget anderledes.



> 
> smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
> Home page is http://smartmontools.sourceforge.net/
> 
> === START OF INFORMATION SECTION ===
> Model Family:     Seagate Barracuda 7200.10 family
> Device Model:     ST3500630A
> Serial Number:    9QG9QLME
> Firmware Version: 3.AAF
> User Capacity:    500.107.862.016 bytes
> Device is:        In smartctl database [for details use: -P show]
> ATA Version is:   7
> ATA Standard is:  Exact ATA specification draft version not indicated
> Local Time is:    Mon Feb  9 23:53:10 2009 CET
> SMART support is: Available - device has SMART capability.
> SMART support is: Enabled
> 
> === START OF READ SMART DATA SECTION ===
> SMART overall-health self-assessment test result: PASSED
> See vendor-specific Attribute list for marginal Attributes.
> 
> General SMART Values:
> Offline data collection status:  (0x82)    Offline data collection activity
>                     was completed without error.
>                     Auto Offline Data Collection: Enabled.
> Self-test execution status:      (   0)    The previous self-test
> routine completed
>                     without error or no self-test has ever
>                     been run.
> Total time to complete Offline
> data collection:          ( 430) seconds.
> Offline data collection
> capabilities:              (0x5b) SMART execute Offline immediate.
>                     Auto Offline data collection on/off support.
>                     Suspend Offline collection upon new
>                     command.
>                     Offline surface scan supported.
>                     Self-test supported.
>                     No Conveyance Self-test supported.
>                     Selective Self-test supported.
> SMART capabilities:            (0x0003)    Saves SMART data before entering
>                     power-saving mode.
>                     Supports SMART auto save timer.
> Error logging capability:        (0x01)    Error logging supported.
>                     General Purpose Logging supported.
> Short self-test routine
> recommended polling time:      (   1) minutes.
> Extended self-test routine
> recommended polling time:      ( 163) minutes.
> 
> SMART Attributes Data Structure revision number: 10
> Vendor Specific SMART Attributes with Thresholds:
> ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE UPDATED 
> WHEN_FAILED RAW_VALUE
>   1 Raw_Read_Error_Rate     0x000f   117   097   006    Pre-fail
> Always       -       142965480
>   3 Spin_Up_Time            0x0003   096   092   000    Pre-fail
> Always       -       0
>   4 Start_Stop_Count        0x0032   100   100   020    Old_age
> Always       -       262
>   5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail
> Always       -       0
>   7 Seek_Error_Rate         0x000f   043   039   030    Pre-fail
> Always       -       7872719137697
>   9 Power_On_Hours          0x0032   100   100   000    Old_age
> Always       -       840
>  10 Spin_Retry_Count        0x0013   100   080   097    Pre-fail
> Always   In_the_past 0
>  12 Power_Cycle_Count       0x0032   100   100   020    Old_age
> Always       -       290
> 187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always
>       -       0
> 189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always
>       -       0
> 190 Airflow_Temperature_Cel 0x0022   066   053   045    Old_age   Always
>       -       34 (Lifetime Min/Max 19/38)
> 194 Temperature_Celsius     0x0022   034   047   000    Old_age   Always
>       -       34 (0 14 0 0)
> 195 Hardware_ECC_Recovered  0x001a   064   060   000    Old_age   Always
>       -       171697002
> 197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always
>       -       0
> 198 Offline_Uncorrectable   0x0010   100   100   000    Old_age
> Offline      -       0
> 199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always
>       -       0
> 200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age
> Offline      -       0
> 202 TA_Increase_Count       0x0032   100   253   000    Old_age   Always
>       -       0
> 
> SMART Error Log Version: 1
> ATA Error Count: 3
>     CR = Command Register [HEX]
>     FR = Features Register [HEX]
>     SC = Sector Count Register [HEX]
>     SN = Sector Number Register [HEX]
>     CL = Cylinder Low Register [HEX]
>     CH = Cylinder High Register [HEX]
>     DH = Device/Head Register [HEX]
>     DC = Device Command Register [HEX]
>     ER = Error register [HEX]
>     ST = Status register [HEX]
> Powered_Up_Time is measured from power on, and printed as
> DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
> SS=sec, and sss=millisec. It "wraps" after 49.710 days.
> 
> Error 3 occurred at disk power-on lifetime: 303 hours (12 days + 15 hours)
>   When the command that caused the error occurred, the device was active
> or idle.
> 
>   After command completion occurred, registers were:
>   ER ST SC SN CL CH DH
>   -- -- -- -- -- -- --
>   84 51 01 01 00 00 a0  Error: ICRC, ABRT 1 sectors at LBA = 0x00000001 = 1
> 
>   Commands leading to the command that caused the error were:
>   CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
>   -- -- -- -- -- -- -- --  ----------------  --------------------
>   c8 00 01 01 00 00 a0 00      00:00:12.271  READ DMA
>   ef 03 45 01 10 00 a0 00      00:00:12.270  SET FEATURES [Set transfer
> mode]
>   ef 03 0c 01 10 00 a0 00      00:00:12.236  SET FEATURES [Set transfer
> mode]
>   c6 da 10 01 4f c2 a0 00      00:00:05.023  SET MULTIPLE MODE
>   b0 da 00 01 4f c2 a0 00      09:10:38.209  SMART RETURN STATUS
> 
> Error 2 occurred at disk power-on lifetime: 303 hours (12 days + 15 hours)
>   When the command that caused the error occurred, the device was active
> or idle.
> 
>   After command completion occurred, registers were:
>   ER ST SC SN CL CH DH
>   -- -- -- -- -- -- --
>   84 51 01 01 00 00 a0  Error: ICRC, ABRT 1 sectors at LBA = 0x00000001 = 1
> 
>   Commands leading to the command that caused the error were:
>   CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
>   -- -- -- -- -- -- -- --  ----------------  --------------------
>   c8 00 01 01 00 00 a0 00      00:00:12.286  READ DMA
>   ef 03 45 01 10 00 a0 00      00:00:12.286  SET FEATURES [Set transfer
> mode]
>   ef 03 0c 01 10 00 a0 00      00:00:12.251  SET FEATURES [Set transfer
> mode]
>   c6 da 10 01 4f c2 a0 00      00:00:10.294  SET MULTIPLE MODE
>   b0 da 00 01 4f c2 a0 00      09:10:38.209  SMART RETURN STATUS
> 
> Error 1 occurred at disk power-on lifetime: 303 hours (12 days + 15 hours)
>   When the command that caused the error occurred, the device was active
> or idle.
> 
>   After command completion occurred, registers were:
>   ER ST SC SN CL CH DH
>   -- -- -- -- -- -- --
>   84 51 01 01 00 00 a0  Error: ICRC, ABRT 1 sectors at LBA = 0x00000001 = 1
> 
>   Commands leading to the command that caused the error were:
>   CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
>   -- -- -- -- -- -- -- --  ----------------  --------------------
>   c8 00 01 01 00 00 a0 00      00:00:12.271  READ DMA
>   ef 03 45 01 10 00 a0 00      00:00:12.271  SET FEATURES [Set transfer
> mode]
>   ef 03 0c 01 10 00 a0 00      00:00:12.236  SET FEATURES [Set transfer
> mode]
>   c6 da 10 01 4f c2 a0 00      00:00:10.399  SET MULTIPLE MODE
>   b0 da 00 01 4f c2 a0 00      09:10:38.209  SMART RETURN STATUS
> 
> SMART Self-test log structure revision number 1
> Num  Test_Description    Status                  Remaining
> LifeTime(hours)  LBA_of_first_error
> # 1  Extended offline    Completed without error       00%       840      -
> 
> SMART Selective self-test log data structure revision number 1
>  SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
>     1        0        0  Not_testing
>     2        0        0  Not_testing
>     3        0        0  Not_testing
>     4        0        0  Not_testing
>     5        0        0  Not_testing
> Selective self-test flags (0x0):
>   After scanning selected spans, do NOT read-scan remainder of disk.
> If Selective self-test is pending on power-up, resume after 0 minute delay.
> 
> 
> 
> 
> 
>